Main Categories
    Filters
    Preferences
    Search

    TinkerKit Sensor Shield V.2

    TinkerKit Sensor Shield V.2 allows you to hook up the TinkerKit Sensors and Actuators directly to the Arduino without the use of the breadboard. It has 12 standard TinkerKit 3 pin connectors.

    MFR Part #: T020010
    $10.99
    Availability: 11 in stock
     

    Features of TinkerKit Sensor Shield V.2

     

    • TinkerKit Sensor Shield V.2 allows you to hook up the TinkerKit sensors and actuators directly to the Arduino, without the use of the breadboard
       
    • It has 12 standard TinkerKit 3 pin connectors.
       
      • 6 connectors (labeled 10-15) are analog inputs
      • 00-05 are analog outputs connected to the PWM capable outputs of the Arduino Board
        • It is possible to change these to digital inputs, in which case they will report either high or low, but nothing in between
           
    • On a Standard Arduino DuemilaNove board the pins are:
       
      • Pin 11 on the Arduino is 00 on the shield
      • Pin 10 on the Arduino is 01 on the shield
      • Pin 9 on the Arduino is 02 on the shield
      • Pin 6 on the Arduino is 03 on the shield
      • Pin 5 on the Arduino is 04 on the shield
      • Pin 3 on the Arduino is 05 on the shield
         
    • A green LED signals that the shield is correctly powered
       
    • Standard 6mm pushbutton allows you to Reset the board
       
    • The 4 pin TWI socket allows communication to any device supporting the I2C protocol through the Wire library on Arduino. 5V and Ground are provided on the socket
       
    • Note: on Arduino the I2C bus uses analog inputs 4 and 5, using the TWI connection precludes the use of those analog inputs
       
    • The 4 pin Serial socket allows the board to communicate with other devices that support serial communication. 5V and Ground are provided on the socket for your convenience
       
    • If you're sending or receiving data to and from the computer this serial connector is not available
       
    • Two mounting holes are provided in the same position found on the Arduino board
       
    • A third hole allows you to see the led connected to pin 13 of the Arduino
    Write your own review
    • Product can be reviewed only after purchasing it
    • Only registered users can write reviews
    *
    *
    • Bad
    • Excellent
     

    Features of TinkerKit Sensor Shield V.2

     

    • TinkerKit Sensor Shield V.2 allows you to hook up the TinkerKit sensors and actuators directly to the Arduino, without the use of the breadboard
       
    • It has 12 standard TinkerKit 3 pin connectors.
       
      • 6 connectors (labeled 10-15) are analog inputs
      • 00-05 are analog outputs connected to the PWM capable outputs of the Arduino Board
        • It is possible to change these to digital inputs, in which case they will report either high or low, but nothing in between
           
    • On a Standard Arduino DuemilaNove board the pins are:
       
      • Pin 11 on the Arduino is 00 on the shield
      • Pin 10 on the Arduino is 01 on the shield
      • Pin 9 on the Arduino is 02 on the shield
      • Pin 6 on the Arduino is 03 on the shield
      • Pin 5 on the Arduino is 04 on the shield
      • Pin 3 on the Arduino is 05 on the shield
         
    • A green LED signals that the shield is correctly powered
       
    • Standard 6mm pushbutton allows you to Reset the board
       
    • The 4 pin TWI socket allows communication to any device supporting the I2C protocol through the Wire library on Arduino. 5V and Ground are provided on the socket
       
    • Note: on Arduino the I2C bus uses analog inputs 4 and 5, using the TWI connection precludes the use of those analog inputs
       
    • The 4 pin Serial socket allows the board to communicate with other devices that support serial communication. 5V and Ground are provided on the socket for your convenience
       
    • If you're sending or receiving data to and from the computer this serial connector is not available
       
    • Two mounting holes are provided in the same position found on the Arduino board
       
    • A third hole allows you to see the led connected to pin 13 of the Arduino