Breadboard Connector Kit for NXT or EV3 is designed to connect NXT or EV3 to a breadboard, soldering required. It contains a PCB, NXT/EV3 compatible connector and headers to attach. This kit also includes an assembly instructions guide.
Adapter Board for Use with the IX-ELVIS
The IX-ELADP is a two channel adapter for interfacing iWorx Systems, Inc. transducers to the stock NI ELVIS II SERIES PROTOTYPING BOARD included with the NI ELVIS system manufactured by National Instruments.
The IX-ELADP is an open PCB with 2 MINIDIN7 connectors that mate to the analog outputs from the transducers. There is also a gain set resistor option.
MXP Breadboard for myRIO is a 300 tie breadboard with a 50 tie bus bar on an expansion card compatible with the myRIO Expansion Port (MXP). The MXP Breadboard functions as an I/O breakout, with digital and analog signals mapped to two headers on either side of the breadboard itself. The MXP Breadboard's connector is also keyed to ensure correct connection with your NI myRIO.
The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier.
The Digilent myProto accessory board for the NI myDAQ and NI myRIO brings all your myDAQ/myRIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.
The MSP connector on your myDAQ / myRIO provides power (+5 VDC and ±15 VDC) along with eight configurable digital I/O pins, two analog inputs, and two analog outputs. All of these signals are available and clearly labeled on the signal blocks at the top of the breadboard when plugged into the MSP connector. Referenece Manual
The mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices. Learn more about mySTEM™ Project Board for NI myDAQ.
Allow you to immediately do some experiments. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Do Engineering Components Kit or visit the Spare Parts Store to create your own project.
Note: mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately.
The Vernier Resistor Board has seven 1 W 5% resistors mounted on a circuit board. Test clip holes on either side of the resistors allow for easy connections to clips on wire leads. The Vernier Resistor Board provides an ideal set of load resistors for KidWind wind turbines and solar panels.
Roll out this mat for an instant, durable, washable canvas. Provides a 100cm x 200cm space for large-scale drawings. Works with Dash, Cue, and Sketch Kit.
Model 9440 Breadboard bundled with JW350 Jumper Wire Kit. 3220 test points; 504 separate 5 point terminals; plus 14 horizontal bus lines. Four color coded binding posts; black; red; yellow and green. 350 pieces pre-stripped; pre-formed solid #22 wire. 14 different length.
Model 9433 Breadboard bundled with JW70 Jumper Wire Kit. 1660 test points; 252 separate 5 point terminals; plus 8 horizontal bus lines. Three color coded binding posts; black; red and green. 70 pieces pre-stripped; pre-formed solid #22 wire.
Model 9425 Breadboard bundled with JW70 Jumper Wire Kit. 830 test points; 126 separate 5 point terminals; plus 4 horizontal bus lines. Three color coded binding posts; black; red and green. 70 pieces pre-stripped; pre-formed solid #22 wire.