Close
Main Categories
    Filters
    Preferences
    Search

    Data Acquisition

    View as Grid List
    Sort by
    Display per page

    BATUltrasonic Sensor Distance Measuring

    #EDU-36734
    $33.95
    (1 In stock)

    This Chemistry Lab Kit includes 8 safe to use chemicals, 80 safety tested experiments. Comes with complete instruction manual

    BITalino 1-lead sensor cable

    #ACCELCTRDCAB
    $11.00
    (11 In stock)

    BITalino 1-lead sensor cableis anindividual cable to connect the sensor pins (IN+, IN-, and REF) to the electrodes.

    Features:

    • Length: 40cm (others possible on request)
    • Sensor connector: Crimp pin (compatible with the individual pins on the Molex Sherlock male plug)
    • Electrode connector: Standard snap on socket

    Breadboard and Jumper Wire Kit

    #9880WK
    $10.95
    (31 In stock)
    This NI Breadboard is a 830 tie point breadboard that comes with a 70 piece jumper wire set designed for use with National Instruments my-DAQ portable data acquisition device.

    Cobra Line Follower Sensor

    #70151
    $9.99
    (7 In stock)

    The Cobra Line Follower Array provides 4 X QRE1113 IR reflectance sensor mounted on a 9mm pitch Each sensor is comprised of two parts - an IR emitting LED and an IR sensitive phototransistor. When you apply power to the VCC and GND pins the IR LED inside the sensor will illuminate.

     

    Danger Shield Complete kits

    #ARD105B1P
    $22.90
    (1 In stock)

    The Danger Shield is an add-on for the [Arduino] micro controller board. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock.

    Electromyography (EMG) Sensor - Connectors: UC-E6

    #SENS-EMG-UCE6
    $26.97
    (2 In stock)

    Purpose-built sensor for muscle activity measurement.

    Features:

    • Voltage differential measurement
    • 3- or 2-lead electrode cable operation (only one REF is needed when using multiple EMGs)
    • Gain: 1009
    • Range: ±1.65mV
    • Bandwidth: 25-482Hz
    • CMRR: 80dB
    • Input impedance: 10GOhm

    Environmental sensor

    #167358
    $99.98
    (In stock)

    fischertechnik Combi-Sensor

    #158402
    $45.24
    (In stock)

    fischertechnik Combi-sensor cobines 3 sensors in one component: triaxial 16bit gyroscope, triaxial 12bit acceleration sensor, compass sensor, I2C connector (9VDC).

    FreaksBotMotor Driver Mainboard (new board)

    #EDU-61021
    $13.95
    (0 In stock)

    The scientific genius of Leonardo da Vinci is brought to life through these 16 articulated models. The inventions that inspired these snap-together replicas are taken from the pages of da Vinci’s priceless and awe-inspiring notebooks. All models are made of plastic and require no special tools. Manuals are very educational and teach how these inventions have evolved into what they are today.

    Grove - Infrared Reflective Sensor v1.2

    #101020174
    $4.90
    (25 In stock)
    Grove - Infrared Reflective Sensor v1.2 can be used for detection of proximity and color of objects. The reflective photosensor - RPR-220 used in this module consists of an infrared light emitting diode and a high –sensitivity phototransistor. Light-colored objects directly in front of the sensor will reflect more infrared light as well as generate more current in the phototransistor than an object with dark-colored surfaces, this can be tell from a built-in indicator LED which will turn red with sufficient flow of current. Also, the intensity of the reflective light increases as the object getting closer. You can adjust the potential-meter on the back of the board if you want to detect a specific object (eg. Black line) at a certain distance.

    IR-Track Sensor, black

    #128598
    $25.84
    (In stock)
    Fischertechnik Spare Part 128598: IR-Track Sensor

    Low Current Sensor Breakout board

    #SEN-08883
    $10.94

    ACS712 series Current Sensor Sensor Evaluation Board

    Mini switch, black

    #37783
    $8.76
    (In stock)
    37783: Mini-Switch

    MXP Breadboard for my-RIO

    #210-283
    $19.99
    (1 In stock)

    MXP Breadboard for my-RIO is a 300 tie breadboard with a 50 tie bus bar on an expansion card compatible with the my-RIO Expansion Port (MXP). The MXP Breadboard functions as an I/O breakout, with digital and analog signals mapped to two headers on either side of the breadboard itself. The MXP Breadboard's connector is also keyed to ensure correct connection with your NI my-RIO.

    myDevBoard - Prototype Board

    #70752
    $44.99
    (401 In stock)

    The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier. 

     

    Includes,

    • NI myDAQ terminal block and female headers
    • 9 V battery holder to add supplemental voltage and current
    • Includes switch to select between battery or external power using AC Adapter or bench top power supply. (Battery, AC adapter and bench top power supply not included)
    • 3 AMP Auto reset fuse
    • Segmented power rails on main bread board
    • Large ground plane underneath main bread board 

    myProto Protoboard

    #6002-410-007
    $84.99
    (7 In stock)

    The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.

    mySTEM Project Board for NI myDAQ

    #13-07-69007
    $129.00
    (In stock)

    The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

     

    Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Do Engineering Components Kit or visit the Spare Parts Store to create your own project.

     

    Includes:

    • S-Motor
    • Mini Switch
    • resisters
    • wires
    • flat plugs

    Note:  mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

    NavX2 MXP Robotics Navigation Sensor

    #71042
    $107.00
    (In stock)

    BRAND NEW NEXT-GENERATION SENSOR NOW AVAILABLE -  leveraging new sensors and state-of-the-art algorithms to deliver a leap forward in accuracy and performance.


    “Generation 2” navX2 MXP is a drop-in replacement for “Classic” navX-MXP, adding significant performance enhancements. See the Frequently Asked Questions (FAQ) for more information about navX2-MXP's new and enhanced capabilities.
     

    *** Feature and Benefits Summary ***

    • 9-Axis Inertial/Magnetic Sensor (Gyro / Accelerometer / Magnetometer)
    • Intelligent Motion Processor
    • RoboRIO Expansion I/O


    Supercharge your robot:  Field-oriented drive, auto-balancing, collision detection, motion detection, auto-rotate-to-angle, linear velocity vectors and more…
     

    Expand your RoboRIO:  10 Digital I/Os, 4 Analog Inputs, 2 Analog Outputs, and TTL UART / I2C / SPI ports.
     

    Plug-n-Play:  easily installed via RoboRIO’s MXP Expansion connector or USB port.
     

    Easy-to-integrate:  C++, Java and Lab View libraries and sample application code simplify integration.
     

    Backwards-compatible:  existing navX-MXP users can upgrade easily.
     

    navX2-MXP is a must-have add on to any RoboRIO-based control system, and includes free software libraries, example code and many more features.
     

    navX2-MXP was designed to use the RoboRIO MXP Expansion Connector - enabling plug-n-play installation on the National Instruments RoboRIO, and adding digital, analog I/O and UART / SPI / I2C port expansion.  navX2-MXP will be compatible with the forthcoming RoboRIO 2.0; for more details, see the Next Generation Control System Update on the FRC Blog.
     

    *** What's New and Improved in navX2-MXP *****

    • Significantly improved yaw accuracy and stability, even during Extreme inertial events.  navX2-MXP features very high-accuracy orientation (yaw/pitch/roll), with minimal yaw drift of ~0.5 degree per minute when moving, and < 0.2 degrees/hour when still.  navX2-MXP is incredibly stable, and averages a yaw drift of only 2 degrees per DAY.  navX2-MXP's new Industrial-class ISM330DHCX IMU sensor handles high rotation (4000 degree/second) and impact (16G, operates in higher temperature environments and can survive extreme shock events (20,000G).
    • Rapid (5-second) auto-calibrating startup.
    • navX2-MXP features an upgraded 180Mhz 32-bit floating-point ARM processor, the new sensors, and new state-of-the-art software algorithms which take navX technology to the next level, including a blazing-fast 416-Khz Kalman Filter, enhanced sensor calibration and algorithms which fuse gyro, accelerometer and magnetometer data into a “9-axis heading”.
    • As a result of these upgrades, the accuracy of Velocity Vector Measurements and Displacement Estimates is also improved.

    NI myRIO Embedded Student Design Device

    #782693-01
    $578.00
    (In stock)

    The National Instruments myRIO-1900 is a portable reconfigurable I/O (RIO) device that students can use to design control, robotics, and mechatronics systems.

    NTC resistor 1.5 k?, silver

    #36437
    $2.15
    (In stock)
    36437: NTC Resistor

    Optical Color Sensor, black

    #128599
    $26.27
    (In stock)
    Fischertechnik Spare Part 128599: Color Sensor

    Photo transistor assembled, yellow

    #36134
    $7.69
    (In stock)
    36134: Photo-Transistor Assembled

    PmodALS: Ambient Light Sensor

    #410-286
    $9.99
    (6 In stock)

    The Digilent PmodALS demonstrates light-to-digital sensing through a single ambient light sensor. Digilent Engineers designed this Pmod around Texas Instrument's ADC081S021 analog-to-digital converter and Vishay Semiconductor's TEMT6000X01.

    Reversing switch, black

    #36708
    $9.37
    (In stock)
    36708: Reversing Switch

    Seeed Studio Grove - 3-Axis Digital Compass

    #SEN12753P
    $14.90
    (2 In stock)
    3-Axis Compass module, a member of grove family uses I²C based Honeywell HMC5883L digital compass. This ASIC is equipped with high resolution HMC118X magneto-resistive sensors and a 12-bit ADC. It provides compass heading accuracy up to 1° to 2°. Signal conditioning like amplification, automatic degaussing strap drivers and offset cancellation are inbuilt. This grove module also includes a MIC5205-3.3 for power supply requirement. Hence user can connect any 3.3V to 6V DC power supply.

    Seeed Studio Grove - BLE (dual model)

    #113020009
    $22.50
    (1 In stock)
    Grove - BLE (dual model) v1.0 uses CSR dual mode Bluetooth chip,with the ARM architecture single chip which supports AT instructions, Users can develop flexibly according to the serial baud rate, equipment name, pairing password.

    Seeed Studio Grove - Blue LED

    #COM04051P
    $1.90
    (4 In stock)

    A general purpose LED module in Grove form factor, available in different colors. The ingenious PCB design enables you to bend the LED to any position you want, which makes it easy to use it standalone, horizontal or Panel Mount(from left to right in below pics)

    Key Specification:

    • Standard Grove connector
    • Operate voltage: 3.3v/5v
    • Emitting Color: Blue

    Seeed Studio Grove - Button

    #COM22242P
    $1.90
    (4 In stock)
    This new version of button twig contains one independent button, which are configured with pull-down resistor ? Ready for use with our microcontrollers as digital input. The button signals the SIG wire,NC is not used on this twig.

    Seeed Studio Grove - Button(P)

    #COM08211P
    $1.90
    (6 In stock)
    What does “P” mean? “P” is for “panel mount” in this product. This Grove – Button is a sister version of original Grove - Button. They are identical except the Grove connecter is moved to the back so that you can easily use it as a neat and wire-free human interface device.

    Seeed Studio Grove - Buzzer

    #COM22458P
    $1.90
    (1 In stock)
    This is a simple yet enjoyable twig to use. The piezo can be connected to digital outputs, and will emit a tone when the output is high. Alternatively it can be connected to an analog pulse-width modulation output to generate various tones and effects.

    Seeed Studio Grove - Dust Sensor

    #SEN12291P
    $15.90
    (22 In stock)
    Sensor is to create Digital (Lo Pulse) output to Particulate Matters (PM). Lo Pulse Occupancy time (LPO time) is in proportion to PM concentration. The output is for PM whose size is around 1 micro meter or larger. We can use the sensor to detect the dust in clean room.

    Seeed Studio Grove - EMG Detector

    #811006001
    $48.00
    (2 In stock)

    EMG detector is a bridge connects human body and electrical, the sensor gathers small muscle signal then process with 2th amplify and filter, the output signal can be recognized by Arduino. You can add this signal into your control system. Note: The sensor cannot be used for medical purposes. In standby mode, the output voltage is 1.5V. When detect muscle active, the output signal rise up, the maximum voltage is 3.3V. You can use this sensor in 3.3V or 5V system.

     

    Key Features:

    • Grove Compatible
    • 3.5mm Connector
    • 6 Disposable Surface Electrodes
    • Power supply voltage: 3.3V-5V
    • 1000mm Cable Leads
    • No additional power supply

    Seeed Studio Grove - Hall Sensor

    #SEN14034P
    $5.90
    (1 In stock)

    The Hall Sensor measures the Hall Effect, which is a production of a voltage difference across an electrical conductor, transverse to an electric current in the conductor as well as a magnetic field perpendicular to the current. The output of the continuous-time switch Hall sensor on this Twig switches low and turns on when a magnetic field (south polarity) perpendicular to the Hall sensor exceeds the BOP threshold, and it switches high and turn on when the magnetic field disappears.

    Key Features:

    • Grove compatible interface
    • 400ns transition period for rise and fall.
    • Continuous-time hall effect sensor

    Application Ideas:

    • RPM meter.
    • Simple dc motor.

    Seeed Studio Grove - I2C ADC

    #INT00100P
    $12.90
    (6 In stock)

    Grove - I2C ADC is a 12-bit precision ADC module based on ADC121C021. It helps you increase the accuracy of value collected from analog sensor by providing a constant reference voltage. Because its address is changeable, you can use up to 9 I2C ADC at the same time at most. At the other hand, this module provides auto sleep function which lowers the power consumption considerably.

    Key Features:

    • Low power consumption
    • High precision
    • Automatic power-down mode
    • Address changeable

    Seeed Studio Grove - I2C Color Sensor

    #SEN60256P
    $19.90
    (2 In stock)

    This module is based on the color sensor TCS3414CS with digital output I2C. Based on the 8*2 array of filtered photodiodes and 16-bits analog-to-digital converters, you can gain the color chromaticity of ambient light or the color of objects. Of the 16 photodiodes, 4 have red filters, 4 have green filters, 4 have blue filters and 4 have no filter(clear). With the synchronization input pin, external pulsed light source can provides precise synchronous conversion control.

    Key Features:

    • Grove compatible interface
    • 16-Bit digital output with I 2C at 400 kHz
    • SYNC Input Synchronizes Integration Cycle to Modulated Light Sources
    • Operating temperature range -40°C to 85°C
    • Programmable interrupt function with User-Defined Upper and lower threshold settings

    Seeed Studio Grove - I2C Hub

    #ACC53133P
    $2.90
    (2 In stock)
    I2C Hub Grove is an extension Grove module for connecting multiply I2C devices to Grove Base Shield. It can use with Universal 4 Pin to X2 4 Pin cable and connects up to 7 I2C divices which may cover most developing purpose.

    Seeed Studio Grove - IR Distance Interrupter

    #SEN09281P
    $5.90
    (5 In stock)
    This IR Distance Interrupter features a high-sensitivity RFR-359F photoreflector to perform distance detection function. The photoreflector consists of a GaAs infared light emitting diode and a silicon planar phototransistor. When the infrared light emitted by the emitter gets reflected on a surface that blocked it, the phototransistor can pick up the signal for distance calculation. This module is panel mounted so that you can easily implement it on the surface of robots or other projects without wiring clutter. Also a potentiometer for adjustment and an indicator LED are arranged on the back for easy and clear use.

    Seeed Studio Grove - LCD RGB Backlight

    #811004001
    $13.90
    (9 In stock)
    Done with tedious mono color backlight? This Grove enables you to set the color to whatever you like via the simple and concise Grove interface. It takes I2C as communication method with your microcontroller. So number of pins required for data exchange and backlight control shrinks from ~10 to 2, relieving IOs for other challenging tasks. Besides, Grove - LCD RGB Backlight supports user-defined characters. Want to get a love heart or some other foreign characters? Just take advantage of this feature and design it!

    Seeed Studio Grove - Mini Fan

    #811005001
    $6.95
    (2 In stock)
    Grove - Mini Fan is a DC motor driver base on AVR microcontroller Atmega168,you can change code by breakout , this module also reserve servo connector,it can driver servo by change code ,Grove - Mini Fan is design for kids, which is use soft fan-leafed in order to avoid unnecessary damage.

    Seeed Studio Grove - OLED Display 0.96"

    #OLE42178P
    $14.90
    (4 In stock)
    Grove - OLED 0.96'' is a 16 color grayscale 96×96 dot matrix OLED display module with Grove compatible 4pin I2C interface.Grove - OLED 0.96" is constructed with 96 x 96 dot matrix OLED module ([ LY120])and SSD1327 driver IC. The characteristics of this display module are high brightness, self-emission, high contrast ratio, slim / thin outline, wide viewing angle, wide temperature range, and low power consumption.

    Seeed Studio Grove - OLED Display 1.12"

    #OLE35046P
    $14.90
    (7 In stock)

    Grove - OLED Display 1.12" is an OLED monochrome 128×64dot matrix display module with Grove 4pin I2C Interface .The characteristics of this display module are high brightness, self-emission, high contrast ratio, slim outline, wide viewing angle, wide temperature range, and low power consumption. It has bigger screen and uses all the columns from the SSD1308 chip so that it can display more contents than the OLED 96×16.

    Key Features:

    • Grove compatible
    • Small size
    • I2C Interface
    • Low power consumption

    Seeed Studio Grove - PIR Motion Sensor

    #SEN32357P
    $7.95
    (4 In stock)
    This is a simple to use PIR motion sensor with Grove compatible interface. Simply connect it to Stem shield and program it, when anyone moves in its detecting range, the sensor outputs HIGH on its SIG pin. The detecting range and response speed can be adjusted by 2 potentiometers soldered on its circuit board, The response speed is from 0.3s - 25s, and max 6 meters of detecting range.

    Seeed Studio Grove - Protoshield

    #PRO23049P
    $1.90
    (0 In stock)
    This protoshield allows you to add your own circuitry or components to your Grove system prototypes. This allows you access to all four lines from the connector cable ? S0, S1, VCC and GND. There is also an extra normally-open button to take advantage of. The hole spacing makes using normal DIP-format ICs and other components very simple. You may wish to purchase more for future use in advance.

    Seeed Studio Grove - Red LED

    #COM04054P
    $1.90
    (4 In stock)

    Grove - LED is designed for the beginners of Arduino/Seeeduino to monitor controls from digital ports. It can be mounted to the surface of your box or desk easily and used as pilot lamp for power or signal. Its brightness can be adjusted by potentiometer.

    Features:

    • Grove compatible interface
    • 3.3V/5V Compatible
    • Adjustable LED orientation
    • Adjustable LED brightness

    Seeed Studio Grove - RTC

    #SEN12671P
    $6.90
    (15 In stock)
    The RTC module is a member of Twig. It is based on the clock chip DS1307 which supports the I2C protocol. It uses a Lithium cell battery (CR1225). The clock/calendar provides seconds, minutes, hours, day, date,month, and year information. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM indicator.

    Seeed Studio Grove - Servo

    #ROB08211P
    $9.90
    (2 In stock)
    Grove - Servo is a bonus product for Grove lovers. We regulated the three-wire servo into a Grove standard connecter. You can plug and play it as a typical Grove module now, without jumper wires clutter. For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your using of the product.

    Seeed Studio Grove - Switch(P)

    #COM08213P
    $2.90
    (3 In stock)
    What does “P” mean? “P” is for “panel mount” in this product. This Grove – Switch is a mini SPDT slide, great for “ON/OFF” situations. It’s such a reliable switch of great build quality that we adopt it on many of our boards. You should stock some for your Grove prototyping system.

    Seeed Studio Grove - Temp&Humi Sensor

    #SEN11301P
    $5.90
    (5 In stock)

    This temperature & humidity sensor provides a pre-calibrated digital output. A unique capacitive sensor element measures relative humidity and the temperature is measured by a negative temperature coefficient (NTC) thermistor. It has excellent reliability and long term stability. Please note that this sensor will not work for temperatures below 0 degree.

    Features:

    • Relative Humidity and temperature measurement
    • Full range temperature compensation Calibrated
    • Digital signal Long term stability
    • Long transmission distance
    • Low power consumption

    Seeed Studio Grove - Temperature & Humidity Sensor -

    #101020074
    $11.50
    (4 In stock)
    This is a multifunctional sensor that gives you temperature and relative humidity information at the same time. It utilizes a TH02 sensor that can meet measurement needs of general purposes. It provides reliable readings when environment humidity condition inbetween 0-80% RH, and temperature condition inbetween 0-70°C, covering needs in most home and daily applications that don't contain extreme conditions.

    Seeed Studio Grove - Water Sensor

    #SEN11304P
    $2.90
    (6 In stock)

    This water sensor module is part of the Twig system. This sensor works by having a series of exposed traces connected to ground and interlaced between the grounded traces are the sens traces. The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not this circuit will work with the digital I/O pins of your Arduino or you can use it with the analog pins to detect the amount of water induced contact between the grounded and sensor traces.

    Features

    • Grove compatible interface
    • Low power consumption
    • 2.0cm x 2.0cm twig module
    • High sensitivity

    Applications Ideas

    • Rainfall detecting
    • Liquid leakage
    • Tank overflow detector

    Seeed Studio Grove Cape for BeagleBone Series

    #811001001
    $19.90
    (6 In stock)
    A true open hardware ,BeagleBone Series is credit-card-sized Linux computer that connects to the Internet and runs software such as Android 4.0 and Ubuntu. With plenty of I/O and processing power for real-time analysis provided by an AM335x 720MHz ARM® processor, BeagleBone can be complemented with cape plug-in boards to augment functionality. And this Grove - Grove Cape for BeagleBone Series is an expansion board for BeagleBone Series to work with abundant Grove resources. There are 6 ready Grove sockets on the board cevering functions like UART, I2C and ADC. And in this way, all Grove Modules are accessible for the BeagleBone board. Wanna make some projects with BeagleBone and need some sensors or display? This Grove - Grove Cape for BeagleBone Series can bring you this convenience.

    Seeed Studio Shield Bot

    #SLD01091P
    $69.90
    (17 In stock)

    Compared with the previous version, The Shield Bot V1.1 can use the usb port of PC to charge battery. And the charging efficiency is greatly improved after we optimize the circuit. And you can use the Arduino/Seeeduino Vin pin to fast charge.

    Note: Compatible Arduino Board not included, try the Seeeduino.

    Seeed Studio Solar Charger Shield v2.2

    #106990020
    $13.50
    (3 In stock)
    The solar charger is a stackable shield to Arduino compatible platforms, enables adaptive battery power and act as energy harvester for in-field charging. You may use various batteries that has the voltage of 3.0V-4.2V to shift up for 5V output, or put on Li-ion battery and solar panel to form an autonomous sensor unit. The maximum current provided by the board can get up to 600mA. An usb connector is also useful to charge the battery.

    Seeed Studio Xadow - UV Sensor

    #SEN07113P
    $12.90
    (8 In stock)
    Xadow UV Sensor is suitable for measuring the UV radiation in sunlight. It can detect the UV wavelength of 290 ~ 400 nm. The UV Sensor is outputting digital voltage value corresponding to UV light intensity. With the diagram of output voltage and UV, we can easy to know the current UV index. The Xadow UV Sensor can be powered by 3.3V. And it is compatible with Xadow system.

    Sharp IR Range Sensor (10cm to 80cm) w/wire

    #40117
    $13.99
    (9 In stock)

    The Sharp IR Distance Sensor GP2Y0A21YK0F uses a beam of infrared light to reflect off an object to measure its distance. Because it uses triangulation of the beam of light to calculate the distance, it is able to provide consistent and reliable readings which are less sensitive to temperature variation or the object’s reflectivity. The sensor outputs an analog voltage corresponding to the distance of the object, and can easily be read using an inexpensive analog to digital converter (ADC) chip.

    Short Lever Limit Switch with Terminals (4 pack)

    #72060
    $9.99
    (10 In stock)

    This is a snap-action micro switch with hinged roller lever and terminals for easy wire connection.

    Studica - Robotics Sensor & Motor Training Kit

    #72031
    $999.00
    (0 In stock)

    The Robotics Sensor & Motor Training Kit from Studica is an affordable and turnkey solution that allows you to teach your students how to control sensors and motors using LabVIEW and NI my-RIO. It includes two project boards, one with different motors and the other board with most of the standard robotics sensors.

    TinkerKit Hall Sensor module

    #T000070
    $6.82
    (10 In stock)

    TinkerKit Hall Sensor module creates a voltage related to the magnetic field around the sensor. This can be used to detect distance from a nearby magnet. Hall sensors can also be used to detect the magnetic field induced in a wire or coil.

    TinkerKit Sensor Shield V.2

    #T020010
    $11.93
    (11 In stock)

    TinkerKit Sensor Shield V.2 allows you to hook up the TinkerKit Sensors and Actuators directly to the Arduino without the use of the breadboard. It has 12 standard TinkerKit 3 pin connectors.

    TinkerKit Tilt Sensor module

    #T000190
    $4.01
    (4 In stock)

    TinkerKit Tilt Sensor module can detect when it is at an angle. This module contains two contacts and a small metal ball. When the sensor is in its upright position, the ball bridges the two contacts, completing the circuit. When the board is tilted, the ball moves, and the circuit opens. When upright, the module outputs 5V and when it is tilted, it outputs 0V. When connected to an input on the Arduino using the TinkerKit Shield, you can expect to read a value of 1023 when in its upright position and 0 when it is titled.

    This module is sensor. The connector is an output, which must be connected to one of the input connectors on the TinkerKit Shield.

    Ultrasonic Distance Sensor

    #70753
    $17.99
    (20 In stock)
    • Stable, accurate distance measurement
    • High precision, blind spots (3cm) super close
    • A full set of ranging process
    • Step File

    Ultrasonic Distance Sensor, black

    #133009
    $50.12
    (In stock)
    133009: Ultra Sonic Sensor TX

    Vernier myDAQ Adapter

    #BT-MDAQ
    $69.00
    (71 In stock)

    The adapter includes two connectors for Vernier analog sensors and one connector for Vernier digital sensors. A screw terminal and header pins provide access to myDAQ lines not used by the connectors. This includes the two analog output lines, three digital lines (including the digital lines with the frequency and pulse width modulation outputs), and a +5 volt power terminal.

    Vernier Resistor Board

    #VES-RB
    $18.00
    (0 In stock)

    The Vernier Resistor Board has seven 1 W 5% resistors mounted on a circuit board. Test clip holes on either side of the resistors allow for easy connections to clips on wire leads. The Vernier Resistor Board provides an ideal set of load resistors for KidWind wind turbines and solar panels.

    2420 Tie Point Breadboard

    #9438
    $29.42
    (20 In stock)

    Features:

    • 2390 Test Points
    • 378 Separate 5 Point Terminals
    • 10 Horizontal Bus Lines of 50 Test Points Each
    • Binding Posts Coded Black; Red; Yellow and Green

    3220 Tie Point Breadboard

    #9440
    $42.87
    (0 In stock)

    Features:

    • 3220 Test Points
    • 504 Separate 5 Point Terminals
    • 14 Horizontal Bus Lines
    • Binding Posts Coded Black; Red; Yellow and Green

    3220 Tie Point Breadboard with Jumper Wire Kit

    #9480WK
    $43.95
    (61 In stock)

    Model 9440 Breadboard bundled with JW350 Jumper Wire Kit. 3220 test points; 504 separate 5 point terminals; plus 14 horizontal bus lines. Four color coded binding posts; black; red; yellow and green. 350 pieces pre-stripped; pre-formed solid #22 wire. 14 different length.

    1660 Tie Point Breadboard with Jumper Wire Kit

    #9483WK
    $21.95
    (18 In stock)

    Model 9433 Breadboard bundled with JW70 Jumper Wire Kit. 1660 test points; 252 separate 5 point terminals; plus 8 horizontal bus lines. Three color coded binding posts; black; red and green. 70 pieces pre-stripped; pre-formed solid #22 wire.

    830 Tie Point Breadboard with JW70 Jumper Wire Kit

    #9485WK
    $15.95
    (7 In stock)

    Model 9425 Breadboard bundled with JW70 Jumper Wire Kit. 830 test points; 126 separate 5 point terminals; plus 4 horizontal bus lines. Three color coded binding posts; black; red and green. 70 pieces pre-stripped; pre-formed solid #22 wire.

    2390 Tie Point Breadboard with Jumper Wire Kit

    #9488WK
    $32.95
    (117 In stock)

    Model 9438 Bredboard bundled with JW140 Jumper Wire Kit. 2390 test points; 378 separate 5 point terminals; plus 10 horizontal bus lines. Four color coded binding posts; black; red; yellow and green. 140 pieces pre-stripped; pre-formed solid #22 wire. 14 different length.

    Analog Protoboard Connector

    #BTA-ELV
    $10.00
    (156 In stock)

    The adapter fits into a standard prototyping board providing easy access to the sensor lines.