The 3D printer that provides you what you really need - efficiency, high quality and easy print removal.

• Easy, safe removal of 3D printed models due to flexible metal build plate

• Maximise utilisation of the machine: Draft mode printing profile allows to print up to 30% faster than low resolution

• Better print results: more intricate and detailed designs with the improved 50 micron ultra high print resolution combined with guided 2-point semi automated leveling

• Optimal safety and less chance for warping of large objects thanks to fully enclosed sturdy plastic design with a 254 x 152 x 170 mm build volume

• No installation needed: Fast out of the box use thanks to the easy setup supported by the user-friendly touchscreen control center on the hardware

Easily remove 3D prints from your Dremel 3D40 FLEX 3D printer's build plate by printing directly onto the Dremel 3D FLEX Build Sheet instead. This pack includes three build sheets, each pre-cut to fit the 3D40 FLEX flexible build plate. You can also use these sheets with the Dremel 3D 3D40-01 and the 3D40-EDU.

Build over 50 Electronic projects including finger touch lamp; metal detector; transistor radio; alarm. Learn about voltage; current; resistors; capacitors and much more. Uses spring hook-up method. This Lab is commonly used in the Bob Jones Home School Curriculum.

Build your own remote control robot controlled by your TV remote! The kit also includes parts for inventing your own robot arm. No soldering required.

Leonardo da Vinci improved upon the already-established catapult design when he introduced his own vision of the age-old military launching device. This design uses a double leaf spring to produce a great deal of energy in order to propel stone projectiles or flammable materials over large distances. A hand crank on the side of the catapult was used to load the spring.

Makeblock 3D Printer nozzle Bracket A is designed specially for use as the bracket for a 3D Printer nozzle. This component is made from 6061 aluminum with a design for proper mounting and room for the nozzle extrusion. It has a high load capacity and is easy to mount.

The NI myDAQ student data acquisition device is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The myDAQ is a high-quality instrumentation device that gives students the power to prototype systems and test circuits outside of the classroom and improve comprehension with continuous reinforcement. (This version of the myDAQ is only for sale to students in the USA).

Special Offer: Optional accessory -  myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.

Special Offer: Optional accessory -  myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.

The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier. 

Includes,

• NI myDAQ terminal block and female headers
• 9 V battery holder to add supplemental voltage and current
• Includes switch to select between battery or external power using AC Adapter or bench top power supply. (Battery, AC adapter and bench top power supply not included)
• 3 AMP Auto reset fuse
• Segmented power rails on main bread board
• Large ground plane underneath main bread board 

The kit comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.

The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.

The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.

Includes:

• S-Motor
• Mini Switch
• resisters
• wires
• flat plugs

Note:  mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

Programmable Xilinx 7020 FPGA NI ELVIS—The NI Engineering Laboratory Virtual Instrumentation Suite (NI ELVIS) III is an engineering laboratory device developed for project-based learning.