Compared with the previous version, The Shield Bot V1.1 can use the usb port of PC to charge battery. And the charging efficiency is greatly improved after we optimize the circuit. And you can use the Arduino/Seeeduino Vin pin to fast charge.

Note: Compatible Arduino Board not included, try the Seeeduino.

The solar charger is a stackable shield to Arduino compatible platforms, enables adaptive battery power and act as energy harvester for in-field charging. You may use various batteries that has the voltage of 3.0V-4.2V to shift up for 5V output, or put on Li-ion battery and solar panel to form an autonomous sensor unit. The maximum current provided by the board can get up to 600mA. An usb connector is also useful to charge the battery.

Xadow UV Sensor is suitable for measuring the UV radiation in sunlight. It can detect the UV wavelength of 290 ~ 400 nm. The UV Sensor is outputting digital voltage value corresponding to UV light intensity. With the diagram of output voltage and UV, we can easy to know the current UV index. The Xadow UV Sensor can be powered by 3.3V. And it is compatible with Xadow system.

The Jog/Shuttle Controller is a human interface device to aid speedy and accurate manual positioning of the axes of the PCNC1100. It serves the role of the device often termed an Electronic Handwheel or MPG.

Telescopic (24 inch) Pick-Up Tool w/ Pocket Clip

TinkerKit Hall Sensor module creates a voltage related to the magnetic field around the sensor. This can be used to detect distance from a nearby magnet. Hall sensors can also be used to detect the magnetic field induced in a wire or coil.

TinkerKit Sensor Shield V.2 allows you to hook up the TinkerKit Sensors and Actuators directly to the Arduino without the use of the breadboard. It has 12 standard TinkerKit 3 pin connectors.

TinkerKit Tilt Sensor module can detect when it is at an angle. This module contains two contacts and a small metal ball. When the sensor is in its upright position, the ball bridges the two contacts, completing the circuit. When the board is tilted, the ball moves, and the circuit opens. When upright, the module outputs 5V and when it is tilted, it outputs 0V. When connected to an input on the Arduino using the TinkerKit Shield, you can expect to read a value of 1023 when in its upright position and 0 when it is titled.

This module is sensor. The connector is an output, which must be connected to one of the input connectors on the TinkerKit Shield.

The Titan Quad Motor Controller is a powerful, 4-channel CAN-based motor controller with a built-in fuse-box (for DC motors up to 20A).

Features:

• 4 x Hardware encoder ports – one for each motor
• 2 limit switch ports for each motor
• Fuse box to set manual current limits
• 2x Power extension ports to power other 12VDC devices. I.E.
  • VMX Robotics Controller
  • Servo Power Module
• Built in LED Controller
• 6A power supply for LED’s
• i2c communication port to control LED Controller
• USB ports are updated to USB-C to better support todays cable standards
• Step File
   

Available for pre-order, shipping in early March 2023.

Specifications:

• 61cm x 38cm x 33cm
• Black
• Heavy duty
• Volume: 53 Liters
• Padlock tabs for added security
• Durable design
• Reinforced removable lid
• Molded grooves for easy and sturdy stacking

Toolkit Wires [100 cm] module are 100 cm long wires designed for TinkerKit with a 3 pin jumper on both sides to easily connect your TinkerKit products.

PathPilot Controller for Tormach PCNC 1100 Mill, PCNC 770 Mill,PCNC 440 Mill and 15L Slant-PRO Lathe.

This kit includes the tools need to cut and join a urethane belt. Recommended for the 5mm Urethane Round Belt - part # 76400.

This kit includes the tools need to cut and join a urethane belt. Recommended for the 5mm Urethane Round Belt - part # 76400

The Goniometer can be used to measure the dynamic motion of a limb during different types of physical activity.

• A set of elastic straps are used to secure the sensor to the subject.
• The lightweight and flexible joint arms allow the limb to move naturally.
• Use it with an EKG Sensor to measure muscle activity during limb motion.
• The sensor can also be detached from the base plate and flexible arms so it can be used in a variety of STEM and engineering activities.

The Low-g Accelerometer is the best choice for most acceleration experiments, including Newton’s second law, simple harmonic motion, and the relationship between acceleration and force. It can also be used to study one-dimensional motion of a car (real and toy), an elevator, a pendulum bob, or an amusement park ride.