Introductory Power NI ELVIS Electronics Device—The Integrator Power Electronics Fundamentals Board for NI ELVIS II/II+ is an add-on application board for the NI Educational Laboratory Virtual Instrumentation Suite II (NI ELVIS II) or NI ELVIS II+ for power electronics applications. The Integrator Power Electronics Fundamentals Board for NI ELVIS II/II+ provides both the hardware and lab resources necessary to teach these topics, giving students all components, wires, and instruments needed conduct experiments. The accompanying software includes all lab instructions and provides students with a simple method of conducting and exporting results of experiments for each lab.

The myGrid for NI myDAQ is an AC power grid that will help a student investigate the components of a power grid. The myGrid interfaces with NI myDAQ to demonstrate energy monitoring, energy conservation, and the concept of the smart grid. The system includes a traditional power source through a motor representing fossil fuels and a renewable power source using a solar panel. It models how power is generated, transmitted, and distributed in a residential setting across three houses.

The myParts kit from Texas Instruments comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.

NI Circuit Design Suite combines Multisim 14.3 and Ultiboard PCB Design Software, to offer students a complete set of tools for circuit design, simulation, validation, and PCB layout. The Circuit Design Suite software download helps you design electronic circuits to final printed circuit board protypes using intuitive and cost-effective tools.

Note: (Only for sale to Students and Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.  No returns or refunds for any download products.)

Programmable Xilinx 7020 FPGA NI ELVIS—The NI Engineering Laboratory Virtual Instrumentation Suite (NI ELVIS) III is an engineering laboratory device developed for project-based learning.

The NI myDAQ student data acquisition device is designed to give students the ability to work on various electronic engineering course work and experiment hands-on with their projects anywhere, anytime. The NI myDAQ is a high-quality electronic lab instrumentation device that gives students the power to prototype electronic systems designs, control systems designs and electronic test circuits outside of the classroom and improve their comprehension with continuous reinforcement. Note: This version of the myDAQ is only for sale to students in the USA.

The National Instruments myRIO-1900 is a portable reconfigurable I/O (RIO) device that students can use to design control, robotics, and mechatronics systems.
 

For motor control, select the MD2 Motor Driver, below in our Add-ons.

The Studica Robotics VMX (part #70176) is a powerful robotics controller with technology for enabling a rich development environment.  The VMX is a Linux-based computing platform with software tools and features enabling access to cutting-edge sensors.

The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.

Includes:

• S-Motor
• Mini Switch
• resisters
• wires
• flat plugs

Note:  mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier.

This student bundle for University of North Dakota - EE313L, includes:

• 1 - 10K OHM 5% 1/4W AXIAL Resistor
• 1 - 1K OHM 5% 1/6W AXIAL Resistor
• 1 - 100 OHM 5% 1/4W AXIAL Resistor
• 1 - 120 OHM 5% 1/4W AXIAL Resistor
• 1 - 200 OHM 5% 1/6W AXIAL Resistor
• 1 - 5 OHM 5% 5W AXIAL Resistor
• 1 - 16K OHM 5% 1/4W AXIAL Resistor
• 1 - CER 1UF 25V X7R RADIAL Capacitor
• 1 - FIXED IND 10MH 170MA 10.86OHM TH
• 1 - FIXED IND 1MH 100MA 20 OHM TH
• 1 - SWITCH SLIDE SPDT 0.4VA 28V
• 1 - CER 10UF 50V X7S RADIAL Capacitor
• 1 - CER 10000PF 400VAC Y5V RAD Capacitor
• 1 - 16 OHM 5% 1/4W AXIAL Resistor
• 1 - Carbon Film 20 Ohm 1/4 Watt 5% Resistor
• 1 - Carbon Film 8.2k Ohm 1/4 Watt 5% Resistor