Main Categories
    Filters
    Preferences
    Search

    myDAQ for Students - Hardware only

    The NI myDAQ student data acquisition device is designed to give students the ability to work on various electronic engineering course work and experiment hands-on with their projects anywhere, anytime. The NI myDAQ is a high-quality electronic lab instrumentation device that gives students the power to prototype electronic systems designs, control systems designs and electronic test circuits outside of the classroom and improve their comprehension with continuous reinforcement. Note: This version of the myDAQ is only for sale to students in the USA.

    Students - Current academic verification is required to purchase this product.

    MFR Part #: 781325-01
    $264.95
    Availability: In stock
     
    Software is Windows only.

    NI myDAQ allows students to work on engineering coursework, prototype electronics control systems, various test circuits, and experiment hands-on with projects anywhere, anytime.

    Here's what is included:

    Two Differential Analog Input and Analog Output Channels (200 ksps, 16 bit, +/- 10 Volts)
    Access matched analog input and output channels in a +/- 10 volt range through the screw terminal connectors or +/- 2 volt range through the 3.5mm audio jacks.
     

    +5 , +15, and -15 Volt Power Supply Outputs (up to 500m Watts of Power)
    USB powered for maximum mobility, myDAQ supplies enough power for simple circuits and sensors.
     

    Eight Digital Input and Digital Output Lines (3.3 Volt TTL-Compatible)
    Use software-timed digital lines for interfacing both Low Voltage TTL (LVTTL) and 5 volt TTL digital circuits. Each line is individually selectable for input or output.
     

    60 Volt Digital Multimeter (DMM) for Measuring Voltage, Current, and Resistance
    The isolated DMM includes the capability to measure both AC and DC voltage and current as well as resistance, diode voltage, and continuity.
     

    Reusable Storage Box with Storage Tray, DMM Probes, and Audio Cable
    The box and storage tray provide convenient storage for your NI myDAQ and included USB cable, DMM probes, audio cable, as well as your own components and accessories.

    View User Guide and Specifications [Click Here]

    What's included:

    • Data Acquisition Device
    • USB Cable
    • DMM Probes
    • Audio cable (3.5mm)
    • Screw Terminal connector and NI screwdriver
    • Getting Started Card
    • TI Design Competition & Samples Program Card
    • Reusable Storage Tray



    The myDAQ is a single data acquisition device that has eight commonly used plug-and-play computer-based electronic lab instruments. With this device, the computer becomes an advanced electronics engineering lab instrument.

    Designed by National Instruments, NI, with high-quality Texas Instruments Analog Integrated Circuits (ICs), the hardware system diagram and list of Texas Instruments IC's in the user guide depicts how TI data converters, amplifiers, and interface and power management circuits were used in the design of NI myDAQ.

    Extend the device's capabilities with LabVIEW and Multisim. Verify homework solutions with real signals using Multisim for circuit simulation and LabVIEW for automating measurements and performing signal processing.

    Technical Support

    Get tips on using the three different software platforms, troubleshoot electronics circuit problems with your NI myDAQ, and/or ask your own questions on the discussion forum - link is listed below.

    Write your own review
    • Product can be reviewed only after purchasing it
    • Only registered users can write reviews
    *
    *
    • Bad
    • Excellent
     
    Software is Windows only.

    NI myDAQ allows students to work on engineering coursework, prototype electronics control systems, various test circuits, and experiment hands-on with projects anywhere, anytime.

    Here's what is included:

    Two Differential Analog Input and Analog Output Channels (200 ksps, 16 bit, +/- 10 Volts)
    Access matched analog input and output channels in a +/- 10 volt range through the screw terminal connectors or +/- 2 volt range through the 3.5mm audio jacks.
     

    +5 , +15, and -15 Volt Power Supply Outputs (up to 500m Watts of Power)
    USB powered for maximum mobility, myDAQ supplies enough power for simple circuits and sensors.
     

    Eight Digital Input and Digital Output Lines (3.3 Volt TTL-Compatible)
    Use software-timed digital lines for interfacing both Low Voltage TTL (LVTTL) and 5 volt TTL digital circuits. Each line is individually selectable for input or output.
     

    60 Volt Digital Multimeter (DMM) for Measuring Voltage, Current, and Resistance
    The isolated DMM includes the capability to measure both AC and DC voltage and current as well as resistance, diode voltage, and continuity.
     

    Reusable Storage Box with Storage Tray, DMM Probes, and Audio Cable
    The box and storage tray provide convenient storage for your NI myDAQ and included USB cable, DMM probes, audio cable, as well as your own components and accessories.

    View User Guide and Specifications [Click Here]

    What's included:

    • Data Acquisition Device
    • USB Cable
    • DMM Probes
    • Audio cable (3.5mm)
    • Screw Terminal connector and NI screwdriver
    • Getting Started Card
    • TI Design Competition & Samples Program Card
    • Reusable Storage Tray



    The myDAQ is a single data acquisition device that has eight commonly used plug-and-play computer-based electronic lab instruments. With this device, the computer becomes an advanced electronics engineering lab instrument.

    Designed by National Instruments, NI, with high-quality Texas Instruments Analog Integrated Circuits (ICs), the hardware system diagram and list of Texas Instruments IC's in the user guide depicts how TI data converters, amplifiers, and interface and power management circuits were used in the design of NI myDAQ.

    Extend the device's capabilities with LabVIEW and Multisim. Verify homework solutions with real signals using Multisim for circuit simulation and LabVIEW for automating measurements and performing signal processing.

    Technical Support

    Get tips on using the three different software platforms, troubleshoot electronics circuit problems with your NI myDAQ, and/or ask your own questions on the discussion forum - link is listed below.

    Customers who bought this item also bought

    Breadboard and Jumper Wire Kit

    #9880WK
    $10.95 $11.50
    ( 28 In stock)
    This NI Breadboard is a 830 tie point breadboard that comes with a 70 piece jumper wire set designed for use with National Instruments my-DAQ portable data acquisition device.

    myParts Kit from Texas Instruments: Companion Parts Kit for NI myDAQ

    #6002-240-001
    $128.25
    ( 17 In stock)

    The kit comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.

    myDevBoard - Prototype Board

    #70752
    $44.99
    ( 119 In stock)

    The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier.

    NI Multisim Circuit Design Suite - Student Edition

    #779897-35
    $65.95
    (In stock)

    NI Circuit Design Suite combines Multisim 14.3 and Ultiboard PCB Design Software, to offer students a complete set of tools for circuit design, simulation, validation, and PCB layout. The Circuit Design Suite software download helps you design electronic circuits to final printed circuit board protypes using intuitive and cost-effective tools.

     

    Note: (Only for sale to Students and Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.)

    myProto Protoboard

    #6002-410-007
    $49.99
    ( 2 In stock)

    The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.

      myGrid for NI myDAQ

      #9mygrid
      $39.95
      ( 242 In stock)

      The myGrid for NI myDAQ is an AC power grid that will help a student investigate the components of a power grid. The myGrid interfaces with NI myDAQ to demonstrate energy monitoring, energy conservation, and the concept of the smart grid. The system includes a traditional power source through a motor representing fossil fuels and a renewable power source using a solar panel. It models how power is generated, transmitted, and distributed in a residential setting across three houses.

      Combo Resistor/Capacitor Kit 465 pcs

      #RCK-465
      $24.95
      ( 7 In stock)

      This combo kit contains a resistor kit RK-365 with 5 each of 73 values for a total of 365 pieces and the capacitor kit CAPK100, which contains 21 varieties of capacitors (ceramic, mylar, and electrolytics) for a total of 100 pieces. Altogether, this kit contains 465 pieces

      micro:bit IO T5 board - ( 8x OUTPUT, 6x INPUT) - INPUT signal to 5V

      #ROB00140-1
      $14.99 $24.95
      ( 9 In stock)

      Board and micro:bit power suply via universal power adapters (6 - 9V) or batteries (6 - 9V).

      Basic Parts Kit

      #CK-1000
      $92.34
      ( 13 In stock)
      This Basic Parts Kit provides you with hundreds of parts to aid you in your prototype needs. Perform experiments first hand and develop a greater understanding of key concepts.