Close
Main Categories
    Filters
    Preferences
    Search

    Data Acquisition

    View as Grid List
    Sort by
    Display per page

    BATUltrasonic Sensor Distance Measuring

    #EDU-36734
    $22.95 $39.95
    (1 In stock)

    This Chemistry Lab Kit includes 8 safe to use chemicals, 80 safety tested experiments. Comes with complete instruction manual

    BITalino 1-lead sensor cable

    #ACCELCTRDCAB
    $11.00
    (11 In stock)

    BITalino 1-lead sensor cableis anindividual cable to connect the sensor pins (IN+, IN-, and REF) to the electrodes.

    Features:

    • Length: 40cm (others possible on request)
    • Sensor connector: Crimp pin (compatible with the individual pins on the Molex Sherlock male plug)
    • Electrode connector: Standard snap on socket

    Breadboard and Jumper Wire Kit

    #9880WK
    $10.95 $11.50
    (41 In stock)
    This NI Breadboard is a 830 tie point breadboard that comes with a 70 piece jumper wire set designed for use with National Instruments my-DAQ portable data acquisition device.

    Cobra Line Follower Sensor

    #70151
    $9.99
    (14 In stock)

    The Cobra Line Follower Array provides 4 X QRE1113 IR reflectance sensor mounted on a 9mm pitch Each sensor is comprised of two parts - an IR emitting LED and an IR sensitive phototransistor. When you apply power to the VCC and GND pins the IR LED inside the sensor will illuminate.

     

    Danger Shield Complete kits

    #ARD105B1P
    $17.95
    (1 In stock)

    The Danger Shield is an add-on for the [Arduino] micro controller board. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock.

    Environmental sensor

    #167358
    $103.53 $102.92
    (In stock)

    fischertechnik Combi-Sensor

    #158402
    $47.86 $47.58
    (In stock)

    fischertechnik Combi-sensor cobines 3 sensors in one component: triaxial 16bit gyroscope, triaxial 12bit acceleration sensor, compass sensor, I2C connector (9VDC).

    Grove - Infrared Reflective Sensor v1.2

    #101020174
    $3.59
    (24 In stock)
    Grove - Infrared Reflective Sensor v1.2 can be used for detection of proximity and color of objects. The reflective photosensor - RPR-220 used in this module consists of an infrared light emitting diode and a high –sensitivity phototransistor. Light-colored objects directly in front of the sensor will reflect more infrared light as well as generate more current in the phototransistor than an object with dark-colored surfaces, this can be tell from a built-in indicator LED which will turn red with sufficient flow of current. Also, the intensity of the reflective light increases as the object getting closer. You can adjust the potential-meter on the back of the board if you want to detect a specific object (eg. Black line) at a certain distance.

    IR-Track Sensor, black

    #128598
    $27.32 $27.19
    (In stock)
    Fischertechnik Spare Part 128598: IR-Track Sensor

    Low Current Sensor Breakout board

    #SEN-08883
    $10.94

    ACS712 series Current Sensor Sensor Evaluation Board

    Mini switch, black

    #37783
    $9.26 $9.22
    (In stock)
    37783: Mini-Switch

    myDevBoard - Prototype Board

    #70752
    $40.48
    (251 In stock)

    The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier. 

     

    Includes,

    • NI myDAQ terminal block and female headers
    • 9 V battery holder to add supplemental voltage and current
    • Includes switch to select between battery or external power using AC Adapter or bench top power supply. (Battery, AC adapter and bench top power supply not included)
    • 3 AMP Auto reset fuse
    • Segmented power rails on main bread board
    • Large ground plane underneath main bread board 

    myProto Protoboard

    #6002-410-007
    $49.99
    (2 In stock)

    The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.

    mySTEM Project Board for NI myDAQ

    #13-07-69007
    $129.00
    (In stock)

    The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

     

    Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.

     

    Includes:

    • S-Motor
    • Mini Switch
    • resisters
    • wires
    • flat plugs

    Note:  mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

    NavX2-MXP Robotics Navigation Sensor

    #71042
    $107.00
    (96 In stock)

    BRAND NEW NEXT-GENERATION SENSOR NOW AVAILABLE -  leveraging new sensors and state-of-the-art algorithms to deliver a leap forward in accuracy and performance.


    “Generation 2” navX2-MXP is a drop-in replacement for “Classic” navX-MXP, adding significant performance enhancements. See the Frequently Asked Questions (FAQ) for more information about navX2-MXP's new and enhanced capabilities.

    NI myRIO Embedded Student Design Device

    #782693-01
    $624.95
    (19 In stock)

    The National Instruments myRIO-1900 is a portable reconfigurable I/O (RIO) device that students can use to design control, robotics, and mechatronics systems.
     

    For motor control, use the MD2 Motor Driver