The 6mm Servo Hub 25T is made of anodized 6061-T6 Aluminum and is used to connect a servo motor to a D-Shaft axel.
The Cobra Line Follower Array provides 4 X QRE1113 IR reflectance sensor mounted on a 9mm pitch Each sensor is comprised of two parts - an IR emitting LED and an IR sensitive phototransistor. When you apply power to the VCC and GND pins the IR LED inside the sensor will illuminate.
The Studica Linear Servo RC Actuator 140-200 is a new Servo motor which has a stroke of 140mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.
The Studica Linear Servo RC Actuator 140-50 is a new Servo motor which has a stroke of 140mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.
The Studica Linear Servo RC Actuator 50-200 is a new Servo motor which has a stroke of 50mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.
The Studica Linear Servo RC Actuator 50-50 is a new Servo motor which has a stroke of 50mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.
The Maverick 12V DC Gear Motor 61:1 w/Encoder was designed for strength to endure competitions, providing a stall torque of 65 min. kgf-cm.
Use the Motor Mount Clamp kit when fastening motors on body and attaching kit to channel and other structure.
The Motor Mount Plate is used with the Maverick 12V DC Gear Motor (Part# 75001) to attach it inside the anyone of the U Channels 76010 to 76018. This is an example of a chassis with 4 motors mounted inside the U-Channel using a Motor Mounting Plate.
Includes,
The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.
The Studica Robot Base Plate is 3mm thick and as with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Servo Mount Flat Plate is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.
The Servo Mount Offset Plate is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.
The Studica Servo Power Module is a 6V, 60W power injector that enables the use of high-power RC servos. The Servo Power Module passes through input signals unaltered while providing up to 60W of total output power across all eight channels. The input and output channels accept standard 3-wire, 0.1” pitch, servo/PWM cables.
Features,
Specifications,
Can be used with 6mm D-Shaft Axel and 6mm shaft DC motor.
Specifcations:
The Sharp IR Distance Sensor GP2Y0A21YK0F uses a beam of infrared light to reflect off an object to measure its distance. Because it uses triangulation of the beam of light to calculate the distance, it is able to provide consistent and reliable readings which are less sensitive to temperature variation or the object’s reflectivity. The sensor outputs an analog voltage corresponding to the distance of the object, and can easily be read using an inexpensive analog to digital converter (ADC) chip.
The 100mm Drive Wheel (4") can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems. Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft. Axles.
The 100mm Drive Wheel (4") can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems. Use with 1/2" hex shaft of use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.
Specifications:
The 100mm (4") Flex Wheel can be used for intake systems and conveyors.
Specifications:
The 100mm (4") Flex Wheel can be used for intake systems and conveyors.
Specifications:
The 100mm (4") Flex Wheel can be used for intake systems and conveyors.
Specifications:
The 100mm (4") Flex Wheel can be used for intake systems and conveyors.
Specifications:
Sometimes you have the need for increased RPM. This 1:1 motor kit can be used with the Studica Maverick or any FTC legal motor such as the Neverest Classic (6600 RPM) or the REV HD Hex motor (6000RPM). The kit includes a faceplate which supports the Studica Robotics building platform. The shaft is press-fit onto the motor's shaft. It is recommended that the shaft be supported by a bearing (we recommend the 76302 for the Studica building system).
Whether you are constructing an intake, designing a shooter, or creating some other high-speed design, this 1:1 option allow you to get the full motor RPM output.
Specifications:
The 120 Degree Bracket is perfect for connecting two channel pieces at 120 degrees from each other. Each side is 48mm wide to fit perfectly on the channel. Use three brackets with 3 channel pieces to make 3 wheeled robots. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
Specifications:
The 135 Degree Bracket is perfect for connecting two channels pieces at 45 degrees from each other. Each side is 48mm wide to fit perfectly on the channel. Used for intake systems, elevator systems, or structure where 45 degrees is required. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica 192mm x 96mm Flat Bracket is a very strong 3mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
Specifications:
Operating Specifications:
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica U Channel is 3mm thick and has a 48mm x 48mm profile. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.
Use with 1/2" hex shaft or use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.
Specifications:
The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.
Use with 1/2" hex shaft or use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.
Specifications:
The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.
Use with 1/2" hex shaft or use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.
Specifications:
The 50mm (2") Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.
Use with 1/2" hex shaft or use 6mm Shaft Hub to use connect 6mm D-Shaft Axles.
Specifications:
Operating Specifications:
Specifications:
The 6mm Shaft hub is used to connect any Studica wheel and the Studica motor or any motor with a 6mm shaft.
Specifcation:
Used with Maverick DC Motor with 6mm shaft and all 6mm D-Shaft Axels. Matching belt 10mm Timing Belt, # 76233.
Specifications:
The 75mm Drive Wheel can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems. Use with 1/2" hex shaft of use6mm Shaft Hubto use connect6mm D-Shaft Axles.
Specifications:
The 90 Degree Bracket is perfect for connecting two channels pieces at 90 angle from each other. Each side is 48mm wide to fit perfectly on the channel. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
90° Clamping Tube Hub provides a great way to attach a 5/8” diameter tube or shaft to a ½" diameter hub. These clamping hubs have a 5/8" diameter bore for shaft connection, a ½" diameter bore for hub connection, four 6-32 tapped holes, four 6-32 through holes, two 6-32 machine screw for tightening, and utilizes the 0.77" hub pattern.
90° Quad Hub Mount C attachesdirectly to a robotics channel in multiple positions and are useful as attachment points for shafts and tubes with a 0.5" diameter and other hub mountable items. The model C type offers a wider base than the model B. Each hub mount has a 0.5" bore, a width of 1.3", and utilizes the 0.77" hub pattern.
The Studica Adjustable Angle Flat Bracket is perfect for connecting two channels pieces together at various angles. It is 3mm thick and as with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Roboticsbuilding components, it has the common hole pattern which makes it easyto connectto other structure with very little or no additional machining required. You can easily connectto other channel, extrusions,bushings, bearing, mounting brackets andmore so you can quickly assemble and disassemble robots and automated systems.
Specifications:
The Studica Square Beam is 8mm by 8mm. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
Aluminum Motor Mount B connects to the outside of robotics channels and works with both standard and precisions gear motors. This allows you to drive shafts through channels, or even tubing. The mount utilizes various hole patterns for your motor, and a 1.5" hole pattern for connecting to other robotics products.
Aluminum Motor Mount D connects to the inside of robotics channels and works with both standard and precisions gear motors. This allows you to drive shafts through channels. The mount utilizes various hole patterns for your motor, and a 1.5" hole pattern for connecting to other robotics products.
Ball Bearing Idler Shaft A includes a pre-installed bearing. It weighs 0.30 oz and measures 0.25" in diameter, 0.55" in height and 1.19" in length. This shaft is an ideal component for your robotic systems.
Includes,
The Bronze Bushing 6mm ID x 14mm OD fits any of the channel and flat brackets having the commoncenter hole pattern of 14mm. The inside diameter will fit any of the D-Shaft axels.
Material:bronze
Inside Diameter:6 mm
Outside Diameter: 14mm
Clamping Swivel Motor Mounts come in 3 sizes (22, 32 and 37mm ID). These motor mounts are extremely versatile and can easily attach to other robotics components. To adjust the height of the motor, simply loosen the pinch bolt found on the clamping swivel motor mount and slide the motor body to the desired position. These motor mounts are constructed of 6061 T-6 aluminum.
The Danger Shield is an add-on for the [Arduino] micro controller board. It contains a variety of fun and useful electronic circuits that you can use to do fun and useful things. It is a fully self-contained shield. You plug it into your Arduino, and you can immediately start using it. No extra things to hook up, no external components. Just a really rad board ready to rock.
Build your own electric powered MOTOR KIT. Control mixing with rotating color disc. Easy to read operating manual. Requires two AA batteries. Ages 8 & Up.
The Studica End Piece Plate is commonly fastened to the inside end of the U Channel. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
Includes,
The Flange Bearing 14mm OD fits any of the channel and flat brackets with the common hole pattern having a center hole of 14mm. The inside diameter will fit any of the D-Shaft axels.
Flanged Ball Bearings are perfect for all robotic channels, hub mounts, or holes that require you to run shafts through. Each order is sold in packs of two. Available in varying sizes.
Futaba Lightweight Hub Horn are ideal for attaching wheels, gears, or any heavy duty servo horns directly to your 3F Futaba servo spline. These aluminum servo hubs have a diameter of 1”, a width of 0.17”, and utilize the 0.77” hub pattern.
Includes,
Hitec Servo Shaft Hub (.500") are perfect for running a hub through a ServoBlock Kit that is directly to your C1 Hitec servo spline. These aluminum servo hubs have a length of 1”, a hub diameter of 1”, a shaft diameter of 0.5”, and utilize the 0.77” hub pattern.
Hitec Standard Hub Horn are ideal for attaching wheels, gears, or any heavy duty servo horns directly to your C1 Hitec servo spline. These aluminum servo hubs have a diameter of 1”, a width of 0.25”, and utilize the 0.77” hub pattern.
Makeblock T6 L256mm Lead Screw and Brass Flange Nut Set can be self-locking, it is suitable for high torque requirements of transmission, such as the aixs for 3D printer. The lead screw also can carry larger load than the threaded rod.
Lightweight Set Screw Hub (3mm Bore) offers 4 equally spaced 6-32 tapped holes and 4 equally spaced 0.14” thru holes. This hub is precision machined from 6061 T6 aluminum. The included set-screw is 6-32 and uses a 1/16” hex key.
Makeblock Linear Motion Block Bracket A serves as a necessary component in a linear motion guide robot. This bracket includes seamless connectivity and flexibility, which is suitable for use in multiple linear motion projects.