Close
Main Categories
    Filters
    Preferences
    Search

    Robotics

    Studica offers a wide variety of robotics parts, kits, as well as structure, motion, and electronics components.

    View as Grid List
    Sort by
    Display per page

    5mm Hex Shaft Hub Kit

    #76288
    $7.99
    (10 In stock)

    This Hub allows user that have existing Studica OMNI wheels (Part# 76260) or Mecanum Wheels (Part# 76243) to use REV Robotics 5mm Hex shafts and Hex Motors.

     

    6mm Servo Hub 25T

    #76149
    $5.99
    (6 In stock)

    The 6mm Servo Hub 25T is made of anodized 6061-T6 Aluminum and is used to connect a servo motor to a D-Shaft axel.

    Cobra Line Follower Sensor

    #70151
    $9.99
    (7 In stock)

    The Cobra Line Follower Array provides 4 X QRE1113 IR reflectance sensor mounted on a 9mm pitch Each sensor is comprised of two parts - an IR emitting LED and an IR sensitive phototransistor. When you apply power to the VCC and GND pins the IR LED inside the sensor will illuminate.

     

    FTC Drive Base Kit

    #70400
    $369.00
    (0 In stock)

    The FTC Drive Base Kit is available for FIRST teams only. This special offer is only available for a limited time and to qualify you must provide us with your FTC team name and number. This drive base kit when purchased individually is valued at $389 USD.

     

    Includes,

    • 2 - 432mm U-Channel  76010
    • 2 - 192mm U-Channel  76015
    • 4 - Motor Mount Plate  76140
    • 2 - End Piece Plate (2pak)  76143-2
    • 1 - 6mm x 96mm D-Shaft (6 pack)  76161-6
    • 2 - M3 x 10mm Button Head Cap Screw (pack of 50)  76203-50
    • 4 - 30 Tooth Bevel Gear (2 Pack)  76219-2
    • 1 - Flange Bearing 6mm ID, 14mm OD, 15mm Flange (12 pack)  76302-12
    • 1 - Collar 6mm ID D-Shaft, 12mm OD (6 pack)  76304-6
    • 1 - Shaft Spacer Plastic 6mm ID x 10mm OD x 1mm L (24 pack)  76305-24
    • 1 - Mecanum Wheel B Set (2 left, 2 right, 100mm, Bearings, w/6mm Hub)  76243

    Note: You can use any FIRST legal motor with this set.

    FTC Starter Kit

    #70402
    $999.00
    (0 In stock)

    FTC Starter Kit offers the ability to create up to three different basic bot designs by Studica.

    The  Starter Kit features many products to allow for a competitive robot to be built by a team. Recommended for groups of 2 to 4 students.

    Linear Servo RC Actuator 140-200

    #75014
    $69.99
    (In stock)

    The Studica Linear Servo RC Actuator 140-200 is a new Servo motor which has a stroke of 140mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

    Linear Servo RC Actuator 140-50

    #75013
    $69.99
    (In stock)

    The Studica Linear Servo RC Actuator 140-50 is a new Servo motor which has a stroke of 140mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

    Linear Servo RC Actuator 50-200

    #75011
    $64.99
    (In stock)

    The Studica Linear Servo RC Actuator 50-200 is a new Servo motor which has a stroke of 50mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

    Linear Servo RC Actuator 50-50

    #75010
    $64.99
    (In stock)

    The Studica Linear Servo RC Actuator 50-50 is a new Servo motor which has a stroke of 50mm. It works the same way as the any standard rotary servo but in a linear movement. It uses the same 2.54mm Dupont 3-Pin Female wire connector and can be controlled with an RC receiver or any device that controls a servo. Includes mounting brackets.

    Maverick DC Gear Motor 60:1 w/Encoder

    #75001
    $28.99
    (7 In stock)

    The Maverick 12V DC Gear Motor 61:1 w/Encoder was designed for strength to endure competitions, providing a stall torque of 65 min. kgf-cm.

     

    Motor Mount Clamp Kit

    #76141
    $10.99
    (12 In stock)

    Use the Motor Mount Clamp kit when fastening motors on body and attaching kit to channel and other structure.

     

    Motor Mount Plate

    #76140
    $6.49
    (9 In stock)

    The Motor Mount Plate is used with the Maverick 12V DC Gear Motor  (Part# 75001) to attach it inside the anyone of the U Channels 76010 to 76018. This is an example of a chassis with 4 motors mounted inside the U-Channel using a Motor Mounting Plate.

     

     

     

     

    Motor Mount Plate Leaf

    #76139
    $4.99
    (14 In stock)

    Motor Pack

    #70263
    $175.00
    (1 In stock)

    Includes,

    • 4 - Maverick 12V DC Gear Motor w/Encoder  75001
    • 4 - Motor Mount Plate  76140
    • 4 - Motor Mount Clamp Kit  76141
    • 1 - M3 x 10mm Button Head Cap Screw (pack of 50)  76203-50

    Multi-Mode Smart Servo

    #75002
    $23.99
    (3 In stock)

    The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

    Robot Base Plate (288mm x 336mm x 3mm)

    #74001
    $38.99
    (6 In stock)

    The Studica Robot Base Plate is 3mm thick and as with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.


    Specifications:

    • Material - Anodized 6061-T6 Aluminum
    • Thickness - 3mm
    • Width - 288mm
    • Length - 336mm
    • Step File