35695: Idler Gear Z 15

36264: Gear Wheel Z 30, M 1,5

The Studica Robotics linear motion shaft of 8mm in diameter and 496mm in length is chrome plated and case hardened; suitable for use with slide units in linear motion applications. The high-carbon steel shaft is chrome plated for corrosion resistance, case hardened for wear resistance, and precision ground for consistent ball bushing radial clearance. Used with Linear Motion Slide Unit 8mm -2 pack

This linear motion closed type slide unit has an 8 mm inside diameter. The slide unit, designed to carry a component, has a housing with a flat mounting face and four tapped bolt holes, and circle clips at each end to retain the ball bushing. Ball in the cage loop to run a smooth ball guide surface to ensure even if high-speed operation, low noise. 

The Maverick 12V DC Gear Motor 61:1 w/Encoder from Studica Robotics is an ideal high torque motor for robotics, designed for strength to endure competitions, with 100rpm and 708 oz-in of torque.

To connect to the REV Robotics Control Hub, the Maverick Encoder Cable (#70163) is required as an Add-on.

Note: This motor is legal for FIRST (FTC) competitions.

The Studica Robotics100mm left-slant Mecanum Wheel is constructed with a blue aluminum frame with yellow rollers and a 6mm Hub.  The wheel is comprised of 9 rollers, able to move in any direction. The rollers are set at 45° to the axis of rotation of the wheel.  

The Studica Robotics100mm right-slant Mecanum Wheel is constructed with a blue aluminum frame with yellow rollers and a 6mm Hub.  The wheel is comprised of 9 rollers, able to move in any direction. The rollers are set at 45° to the axis of rotation of the wheel.  

The Studica Robotics Motor Mount Clamp kit is used for fastening motors on the body of your robot and attaching the kit to a channel and/or other structures.

The Studica Robotics Motor Mount Plate is used with the Maverick 12V DC Gear Motor to attach to the inside any U-Channels.

The Studica Robotics Motor Mount Plate Leaf is used with the Maverick 12V DC Gear Motor to attach to the inside any U-Channels. 

The Studica Robotics Motor Pack includes all you need to connect to your robotics model for use in classroom learning and competitions.

4 Maverick 12V DC Gear Motor w/Encoder (part #75001) are included.

The Studica Robotics Multi-Mode Smart Servo Motor features all-steel gears with lots of torque. 

Note: This servo motor is legal for FIRST (FTC) competitions.

The Studica Robotics 100mm (4 inch) Omni Wheel provides rotational and sideways 360° maneuverability.  Great for omni directional movement and rotation, easy direction control and tracking, and for fast turning. Use the Enhanced Wheel D-Shaft Hub Kit with this Omni Wheel.

The Studica Robotics Pro Gear Pack includes 13, 26 and 30 tooth bevel gears, rack & pinion, shaft hubs and socket head cap screws, ideal for your robotics designs.

The Studica Robotics Servo Mount Flat Plate is designed to mount the Multi-Mode Smart Servo (part #75002) to the Studica building structure.

The Studica Robotics Servo Mount Offset Plate is used to mount the Multi-Mode Smart Servo (part #75002) to the Studica building structure.

Includes,

• 8 - Multi-Mode Smart Servo Motors 75002
• 1 - Smart Robot Servo Programmer  75003
• 1 - 6V DC AA Battery Holder w/TJC8 Female, 22 AWG  75004
• 1 - Servo Power Block  75006
• 4 - Servo Standard Front Mount  76144
• 4 - Servo Mount Flat Plate  76145
• 4 - Servo Mount Offset Plate  76146
• 8 - Servo Horn 25T  76148
• 8 - 6mm D-Shaft Servo Hub 25T  76149

The Servo Power Block is a 6V, 60W power injector that provides proper power for RC Servos. It does not interfere with the signal, it will only replace the power to the servo with 6V. 

The Servo Standard Front Mounting Bracket is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

The Studica Robotics D-Shaft Coupling has an ID of 6mm and an OD of 12mm.  It can be used with the 6mm D-Shaft Axle and a 6mm shaft DC motor. 

This Studica Robotics 1mm nylon spacer 24-pack is used to space gears, sprockets, wheels, and other parts along a 6mm D-shaft. Mix and match with various spacer lengths.

This 20mm Spacer is used to space gears, sprockets, wheels, and other parts along a 6mm D-shaft. Mix and match various spacer lengths.

This 1mm Spacer is used to space gears, sprockets, wheels, and other parts along a 6mm D-shaft. Mix and match various spacer lengths.

This 1mm Spacer is used to space gears, sprockets, wheels, and other parts along a 6mm D-shaft. Mix and match various spacer lengths.

The Studica Smart Robot Servo Programmer is used for programming the Studica Multi-Model Smart Servo Motor and for testing other standard Servos. Use it to program the Studica Servo motors to switch between continuous mode, standard mode, or any custom angular mode.  

Specifications:

• Requires 6 Volt battery pack with TJC8 connector or use the Studica 6V DC Battery Holder.
• Programming setting modes
  • Standard
  • Continuous
  • Angular

The XL series belt is compatible with the 6mm, 10 tooth XL pulley.

Specifications:

• Material: Neoprene with Fiberglass cords
• Length: 1 meter
• Width: 9mm

The Studica Robotics 100mm Drive Wheel (4"), with a 12.5mm axial width can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems.  Use with 1/2" hex shaft or use a 6mm Shaft Hub to connect to 6mm D-Shaft axles.

The Studica Robotics 100mm Drive Wheel (4") with an axial width of 25mm, can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems. Use with 1/2" Hex Shaft or 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

The Studica Robotics 100mm Flex Wheel (4"), with a 25mm axial width can be used for intake systems and conveyors with your robotics design builds.

The Studica Robotics 100mm (4") orange Flex Wheel with an axial width of 25mm and a durometer of 40A can be used for intake systems and conveyors.

The Studica Robotics 100mm (4") blue Flex Wheel with an axial width of 25mm and a durometer of 50A can be used for intake systems and conveyors.