The Studica Robotics 10-tooth Pulley includes two 5mm Bores, two 10-Tooth Aluminum Pulleys and one 1M XL Timing belt.

The Studica Robotics 10mm OD round groove D-shaft pulley is for use with your robot design builds.

The Studica Robotics 1:1 motor mounting plate kit can be used with the Studica Maverick or any FTC legal motor such as the Neverest Classic (6600 RPM) or the REV HD Hex motor (6000RPM). 

The Studica Robotics 1-1 Motor D-Shaft Kit can be used with the Studica Maverick or any FTC legal motor such as the Neverest Classic (6600 RPM) or the REV HD Hex motor (6000 RPM). The kit includes a faceplate which supports the Studica Robotics building platform. The shaft is press-fit onto the motor's shaft. It is recommended that the shaft be supported by a bearing (part # 76302 for the Studica building system).

The Studica Robotics 110mm All-Terrain Rubber Wheel Tire includes a 6mm adapter. It has a foam core and therefore does not require air.

A 128 tooth gear for robotics design, made from 6061-T6 aluminum, with a 6.35mm thickness and a 14mm hole diameter.

The Studica Robotics 20mm OD round groove D-shaft pulley is for use in robot design builds.

The 250 mm Linear Slide Set from Studica Robotics provides high-precision, low-friction linear motion — perfect for robotics, automation systems, and STEM builds. With a stainless-steel guide rail and ball-bearing block, this slide rail kit delivers smooth, repeatable motion for lifts, arms, linear actuators, or any mechanism requiring reliable linear travel.

A Studica Robotics 26-tooth bevel gear for use in robotics design and competitions.

The Studica Robotics 30-tooth bevel gear, 1-1 set (2 pack) is ideal for robotics design builds.

The Studica Robotics 30mm OD round groove D-shaft pulley is for use with robotics design builds. 

The Studica Robotics 32-tooth gear (2-pack) is ideal for use with robotics design builds.

The 400 mm Linear Slide Set from Studica Robotics provides high-precision, low-friction linear motion — perfect for robotics, automation systems, and STEM builds. With a stainless-steel guide rail and ball-bearing block, this slide rail kit delivers smooth, repeatable motion for lifts, arms, linear actuators, or any mechanism requiring reliable linear travel.

The Studica Robotics 40mm OD round groove D-shaft pulley is for use with your robotics design builds.

The Studica Robotics 50mm OD round groove D-shaft pulley is for use with your robotics design builds.

The Studica Robotics 5mm 10-tooth pulleys are .40” inside the flanges to allow for belts up to 3/8” in width. Includes two set screws using a 1.5mm hex key.

The Studica Robotics 5mm Hex Shaft Hub allows users that have existing Omni Wheels (Part# 76260) or Mecanum Wheels (Part# 76243) to use REV Robotics 5mm Hex Shafts and Hex Motors.

The Studica Robotics 60mm OD round groove D-shaft pulley is for use with your robotics design builds.

A Studica Robotics 64-tooth gear (2 pack), for use with robotics design builds.

The Studica Robotics 6mm D-Shaft Servo Hub 25T is made of anodized 6061-T6 Aluminum and is used to connect a servo motor to a D-Shaft axle.

The 6mm D-Shaft Hub from Studica Robotics is a precision aluminum mounting hub that connects a 6mm D-shaft to wheels or robot components. Ideal for a secure shaft to mounting hub connection. Sold in a pack of 4.

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

The Studica Robotics 6mm x 432mm D-Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

The 6mm diameter D-Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

The 6mm x 96mm D-Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

The Studica Robotics 6mm, 10-tooth XL Pulley (2 pack) is ideal for use with the Maverick DC Motor with a 6mm shaft and all 6mm D-Shaft Axles. 

Use it to power the Studica Smart Robot Servo Programmer or any other device requiring 6V output and a TJC8 connector. 

Specifications:

• 6V Output
• On/Off Power switch
• TJC8 connector
• Uses 4 x 1.5V AA Batteries (not included)

The Studica Robotics Bronze Bushing 6mm ID x 14mm OD fits any of channel or flat bracket having the common center hole pattern of 14mm. The inside diameter will fit any of the D-Shaft axles.

The Studica Robotics bronze bushing 12-pack is ideal for robotics design builds.

The Studica Robotics D-Shaft Collar is 6mm ID and 12mm OD. The inside diameter will fit any of the D-Shaft axles.

The 6mm ID Round Flanged Bearing fits any of the channel and flat brackets with the common hole pattern having a center hole of 14mm. The inside diameter will fit any of the D-Shaft axles.

The Studica Robotics Gear Pack includes 32, 64 and 128 tooth gears, D-shaft hubs and socket head cap screws, ideal for your robotics designs.