Main Categories
    Filters
    Preferences
    Search

    Circuit Design

    Circuit Design

    View as Grid List
    Sort by
    Display per page

    NI Multisim Circuit Design Suite Student Edition

    #779897-35
    $68.95
    (In stock)

    NI Circuit Design Suite Student Edition combines Multisim 14.3 and Ultiboard PCB Design Software, to empower students with a complete set of professional tools from schematic circuit design, circuit simulation and validation, also includes UltiBoard advanced PCB layout software. The Circuit Design Suite software download is a complete EDA solution that helps students create and test designs from electronic circuits to final printed circuit board protypes using the latest professional intuitive and cost-effective electronic engineering tools.

     

    Note: (Only for sale to Students and Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.  No returns or refunds for any download products.)

    Analog Discovery 3

    #410-415
    $249.00
    ( 24 In stock)

    Discover More with the New Analog Discovery 3 for Education

     

    Digilent’s latest multi-function test and measurement device, also known as the AD3, is a digital oscilloscope, logic analyzer, waveform generator, pattern generator, and much more. Using the flexible WaveForms software (supported by Windows, Mac, and Linux), the Analog Discovery 3 can be used in the lab, in the field, or even at home - you're no longer tied down to a traditional benchtop and stacks of expensive test instruments.

    Arduino Uno R3

    #A000066
    $14.95 $27.60
    ( 150 In stock)
    The Arduino Uno R3 is a microcontroller board. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter.

    Arduino Uno SMD Rev3

    #A000073
    $14.95 $26.30
    ( 11 In stock)

    Arduino Uno SMD Rev3 is a microcontroller board based on the ATmega328. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from preceding boards in that it does not use the FTDI USB-to-serial driver chip.

    70 pc. Jumper Wire Kit

    #JW-70
    $3.95 $5.50
    ( 1 In stock)

    Jumper Wire Kit for Breadboard prototyping contains 70 pieces of pre-stripped; pre-formed #22 solid wire in assorted colors and lengths. Storage case included.

    Elenco Digital Multimeter

    #M-1000E
    $14.95
    ( 45 In stock)

    Compact Digital Multimeter now with LARGER 1" display. Key Features: 7 Functions / 17 measuring ranges, Larger 1" display, 0.5% Basic accuracy, 1M? input impedance, Overload protection, Transistor test, Pocket-size, and Audible continuity test.

    myGrid for NI myDAQ

    #9mygrid
    $39.95
    (In stock)

    The myGrid for NI myDAQ is an AC power grid that will help a student investigate the components of a power grid. The myGrid interfaces with NI myDAQ to demonstrate energy monitoring, energy conservation, and the concept of the smart grid. The system includes a traditional power source through a motor representing fossil fuels and a renewable power source using a solar panel. It models how power is generated, transmitted, and distributed in a residential setting across three houses.

    UND Basic Parts Bundle for EE206L (NI myDAQ not included)

    #UND-EE206L
    $99.00
    This student bundle for University of North Dakota students includes:
    • 1- 140 piece Jump Wire Kit
    • 1- 370 piece 1/4W Resistor Kit
    • 1- 100 piece Capacitor Component Kit
    • 1 - Choke, Axial, Conformal, 1000 uH 5% Inductor
    • 2 - 1000 pF 100 Volt Silver Mica Capacitor BC# 8860720
    • 3 - Inductor, Toroid, Vertical, 1000.0 uH, 1.3 IDC, 0.4 OHM
    • 3 - IC OP amp GP 1MHZ 8DIP
    • 1 - 9V battery
    • 1 - Alligator Clips

    UND Course Electronics I & II EE321L/EE421L Lab Equipment - Supplies kit without myDAQ (NI myDAQ is not included in this price option)

    #UND-EE321L-EE421L
    $199.00

    NI myDAQ student bundle for University of North Dakota students includes:
    5 - 100 Ohm  Resistors
    5 - 120 Ohm  Resistors
    5 - 390 Ohm  Resistors
    5 - 500 Ohm  Resistors
    2 - 510 Ohm  Resistors
    10 - 1k Ohm Resistors
    10 - 5k Ohm Resistors
    5 - 10k Ohm Resistors
    3 - 11k Ohm Resistors
    3 - 20k Ohm Resistors
    5 - 50k Ohm Resistors
    5 - 75k Ohm Resistors
    3 - 82k Ohm Resistors
    5 - 100k Ohm Resistors
    5 - 300k Ohm Resistors
    5 - 500k Ohm Resistors
    3 - 1M OHM Resistors
    3 - 1NA126P op-amp array
    10 - 4148 diodes
    4 - Zener diodes (3V)
    4 - Zener diodes (5V)
    6 - ZVN2110A N-channel MOSFETs
    2 - 4007 CMOS arrays-dual complimentary pair plus inverter
    7 - 3906 transistor arrays
    15 - 2N3904 BJTs
    9 - 2N3906 BJTs
    6 - 741 operational amplifiers
    2 - 500k potentiometers/variable resistors
    10 - ZVN2106 MOSFETs
    8 - through-hole LEDs
    1 - 9V battery

    PmodUSBUART USB to UART Interface

    #410-212
    $9.99 $11.99
    ( 1 In stock)

    FT232R Serial to USB Interface Pmod™ Platform Evaluation Expansion Board

    myDigital Protoboard for NI myDAQ & myRIO

    #6002-410-006
    $99.00
    (In stock)

    The Digilent myDigital accessory board for the NI myDAQ and NI myRIO is designed to provide students a cost-effective, portable, and engaging platform for teaching electronics. With a myDAQ / myRIO, NI Multisim, and a myDigital, you'll have everything needed to allow students to design, construct, and test basic analog and digital designs. 

    Circuit Design

    Refine
    8 More