Close
Main Categories
    Filters
    Preferences
    Search

    Electronics

    Electronics

    View as Grid List
    Sort by
    Display per page

    34 Pin MXP extender cable - 8 inch

    #69003
    $3.99

    Extend the reach of your MXP port by using this 8 inch cable to re-position you boards where you need them.

    Compatable with MXP accessory boards like the protoboard, RIOduino and myRIO.

    Features:

    • Keyed male and female 34-pin connectors
    • 28 AWG ribbon cable
    • 34 conductor
    • 8″ length

    6mm Servo Hub 25T

    #76149
    $5.99

    The 6mm Servo Hub 25T is made of anodized 6061-T6 Aluminum and is used to connect a servo motor to a D-Shaft axel.

    DC Power Plug 2.1mm ID x 5.5mm OD w/1m 18AWG cable

    #70016
    $3.49

    Ideal for the myRIO.

    • Inside Contact Diameter: 2.1mm
    • Outside Contact Diameter: 5.5mm
    • Termination Style: Solder Cup
    • Voltage Rating: 12 V
    • 6 Amp
    • 1 meter cord length
    • 18AWG or 20AWG wire guage
    • DC connector type

    First Person View Kit - FPV2

    #70136
    $299.00

    Studica First Person View (FPV) System for WorldSkills Mobile Robotics.

    Featuring a Small lightweight video transmitter, 650TVL Camera with 2.8mm Wide angle lenses, and a 7-inch LCD HD screen.

    MAIN FEATURES

    • LCD
      • Small and lightest video transmitter
      • 5V-22V input
      • 25mW / 200mW power settings
      • Ultra-clean transmission
      • Robust RF amplifier
      • Clean powerup and video switching
      • LCD screen feature integrated 5.8Ghx Dual Diversity Receiver and automatic signal search (Supports 40 channels)
    • Camera
      • "Zero" latency (less than 1ms end to end)
      • 650 TVL - the highest possible resolution without adding additional latency
      • Tuned both for day and night flying
      • 2.8mm wide angle lens
      • Lightweight plastic enclosure, matching popular older cameras for mounting compatibility
      • Wide voltage input range (5V - 22V)
    • 5G8 MMCX Linear Antenna with MMCX connector
    • UNIFY PRO 5G8 HV Video Transmitter
      • ​Smallest, lightest video transmitter on the market
      • 2-6S input power supported
      • 25mW / 100mW / 400mW power settings
      • Integrated heat sink
      • Ultra-clean transmission (up to 16 pilots at once!)
      • PitMode - power up your quad during a race
      • Easy OSD, FC and RC channel changes, with fallback button menu
      • Robust RF amplifier allows powering up without antenna for hours!
      • Clean powerup and video switching
    • CE certified

    Maverick DC Gear Motor 60:1 w/Encoder

    #75001
    $28.99

    The Maverick 12V DC Gear Motor 60:1 w/Encoder was designed for strength to endure competitions, providing a stall torque of 65 min. kgf-cm.

    Specifications:

    • Voltage:                        12 volts
    • Length:                         127.5mm
    • Gear Ratios:                 60:1
    • Axel diameter:             6mm D-Shaft
    • Diameter:                     37mm
    • Stall Torque:                 65 min. kgf-cm (902 oz-in)
    • RPM:                               100
    • Encoder:                        high-resolution Hall effect, 12ppr, total count 732 per shaft rotation
    • Weight:                          0.33kgs
    • Power cable:                 PP45, 45cm, 14AWG
    • Encoder Cable:             45cm, 22AWG
    • Step File

    Motor Mount Clamp Kit

    #76141
    $10.99

    Use the Motor Mount Clamp kit when fastening motors on body and attaching kit to channel and other structure.

     

    Motor Mount Plate

    #76140
    $6.49

    The Motor Mount Plate is used with the Maverick 12V DC Gear Motor  (Part# 75001) to attach it inside the anyone of the U Channels 76010 to 76018. This is an example of a chassis with 4 motors mounted inside the U-Channel using a Motor Mounting Plate.

     

     

     

     

    Motor Mount Plate Leaf

    #76139
    $4.99

    Motor Pack

    #70263
    $175.00

    Includes,

    • 4 - Maverick 12V DC Gear Motor w/Encoder  75001
    • 4 - Motor Mount Plate  76140
    • 4 - Motor Mount Clamp Kit  76141
    • 1 - M3 x 10mm Button Head Cap Screw (pack of 50)  76203-50

    Multi-Mode Smart Servo

    #75002
    $23.99

    The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

    Specifications:

    Type:                             Metal Brush Motor
    Horn Gear Spline:       25T (5.9mm)
    Size:                               40mm x 20.1mm x 38.3mm
    Weight:                          65g
    Maximum Speed:        62RPM at 6V
    Stall Torque:                 20kg.cm at 6V
    Voltage:                         6-7 4V
    Cable:                             22AWG, 75cm

    myDAQ 20 Pin Screw Terminal Block Connector

    #70161
    $7.49

    Used to replace or supplement connector on NI myDAQ Kit

    NiMH Battery Pack Charger, PP45

    #70019
    $29.99

    The Studica NiMH Battery Pack Charger, PP45, is used to recharge the 12V 3,000 mAh NiMH Battery Pack, PP45.  

    Specifications

    • Rating AC Input: 100V to 240V AC, 0.6A RMS, 50/60 Hz
    • Rating Output: 7V to 16 VDC
      • 0.9A to 1.8A
    • Protection mode: output short circuit protection and output polarity reverse protection.
    • Temperature range 0C ~+40C (battery pack)
    • Operate Humidity: 5% ~ 90%

    LED Indication

    Red Normal Main Charge mode
    Green Normal Finished / Open mode
    Red / Green Flashing Short Circuit

    Power Control Panel

    #70170
    $59.00

    Power Control Panel for WorldSkills Mobile Robot

    • Blue panel
    • Emergency Stop
    • Green and red indicator lights showing Stopped and Running states
    • On/Off Switch
    • Three momentary switches for stopping, starting and resetting

    Power Switch

    #70183
    $2.99

    On/Off Power Switch

    Power Switch Plate

    #70184
    $4.99

    Power Switch Plate for Power Switch # 70183

    Powerpole 45 Extension Cable, 14AWG, 50cm

    #70021
    $9.99

    The Powerpole Extension Cable is 50cm long and 14AWG wire gauge to handle heavier loads.

    PWM cable Set - TJC8 3 pin, 22AWG, F-F - 12 pcs

    #71011
    $15.99

    This set of 12 pieces includes,

    • 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 6 x 3pin Dupont male to male connectors

    Remote Control Device

    #70111
    $19.99

    A familiar button layout brings console-style control to your robot controls. All the controls are just where you expect them to be thanks to the standard button layout of this control.

    XINPUT MODE:

    • A, B, X, Y buttons
    • LB, RB buttons
    • Left and right analog triggers
    • Start and Back buttons
    • Two clickable analog mini-joysticks
    • 8-way D-pad
    • Home button
    • Sports mode

    DIRECTINPUT MODE:

    • 10 programmable buttons*
    • Programmable left and right triggers*
    • Two programmable analog mini-joysticks*
    • 8-way programmable D-pad*
    • Sports mode

    Servo Horn 25T

    #76148
    $3.99

    The Servo Horn 25T is used with the Multi-Mode Smart Servo (75002) and the Studica building structure.

     

     

    Servo Mount Flat Plate

    #76145
    $6.49

    The Servo Mount Flat Plate is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

     

    Servo Mount Offset Plate

    #76146
    $6.99

    The Servo Mount Offset Plate is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

     

    Servo Pack

    #70254
    $339.00

    Includes,

    • 8 - Multi-Mode Smart Servo  75002
    • 1 - Smart Robot Servo Programmer  75003
    • 1 - 6V DC AA Battery Holder w/TJC8 Female, 22 AWG  75004
    • 1 - Servo Power Block  75006
    • 4 - Servo Standard Front Mount  76144
    • 4 - Servo Mount Flat Plate  76145
    • 4 - Servo Mount Offset Plate  76146
    • 8 - Servo Horn 25T  76148
    • 8 - 6mm D-Shaft Servo Hub 25T  76149

    Servo Power Block

    #75006
    $36.99

    The Studica Servo Power Module is a 6V, 60W power injector that enables the use of high-power RC servos. The Servo Power Module passes through input signals unaltered while providing up to 60W of total output power across all eight channels.  The input and output channels accept standard 3-wire, 0.1” pitch, servo/PWM cables. 

    Features,

    • Built in DC-DC converter
    • Over-current shutdown
    • ESD protection

    Specifications,

    • Nominal Input Voltage: 12V
    • Operational Voltage Range: 6.0V
    • Number of Channels: 8
    • Max Current for All Channels Combined: 10A
    • Total Continuous Power: 60W
    • Size: 70mm x 45mm x 16mm
    • Step File

     

    Servo Standard Front

    #76144
    $4.49

    The Servo Standard Front Mounting Bracket is one option to mount the Multi-Mode Smart Servo (75002) to the Studica building structure.

     

    Smart Robot Servo Programmer

    #75003
    $12.99

    The Studica Smart Robot Servo Programmer is used for programming the Studica Multi-Model Smart Servo Motor and for testing other standard Servos. Use it to program the Studica Servo to switch between continuous mode, standard mode, or any custom angular mode.  

    Specifications:

    • Requires 6 Volt battery pack with TJC8 connector or use the Studica 6V DC Battery Holder.
    • Programming setting modes
      • Standard
      • Continuous
      • Angular

    SR-Pro 8MP Camera

    #71045
    $179.99

    The Studica SR-Pro 8mp Camera with CSI to HDMI Adapter board was designed for the VMX-Titan Robotics Platform for WorldSkills, and Raspberry Pi hardware. 

    Features and Specifications:

    • Camera:
      • Optical Size - 1/4’’
      • Resolution - 8mp
      • Frame Rate - 1080p30, 720p60 and 640 × 480p60/90
      • Field of View (FOV) - 75 degrees (Horizontal)
      • Lens Mount - M12
      • IR Sensitivity - Visible Light Only
      • Step File
         
    • CSI-HDMI Adapter Board:
      • Supports Raspberry Pi 4B, Pi 3B+, Pi 3B, Pi 2, Model A/B/B+
      • Support Raspberry Pi 5MP OV5647/8MP IMX219/12MP IMX477 camera
      • HDMI - High Speed - 1M length
      • Reserved microphone and headphone jack for audio or GPIO signals
      • Three additional solder pads are available (same signals as headphone jack

    Titan Wire Pack

    #70162
    $4.99

    USB Cable, Type A to Type C, Blue, 2M

    #70186
    $5.99

    USB Cable, Type A to Type C, Blue, 2 Meters, male to male

    VMX Battery Adapter Cable

    #70167
    $2.99

    Part# 70167

    The VMX Battery Adapter cable connects a VMX-pi power connectcor to an external battery supply.

    Detailed Specifications:

    • Cable Length: 25 cm
    • Wire Gauge: 20 AWG
    • Connector: JST-VH Wire Colors: Red (power), Black (ground)
    • Wire Free-end:  stripped and tinned

    VMX Cable Pack

    #70160
    $49.99

    Includes:

    • 4 JST-GH Cables (connects a VMX-pi GH signal connector to an external sensor or device such as the VMX breakout board).
    • 1 battery adapter cable (connects a VMX-pi power connector to an external battery supply).
    • 1 Wallwart cable (cable allows you to connect a VMX-pi to an external 12VDC Wallwart power supply).
    • 4 JST-GH to AMP breakout boards (connects a 4-pin .1" standard connect (Dupont/AMP).  The connector may either be a standard or a locking variety connector. Use to connect components such as an Ultrasonic Sensor or Encoders.

    VMX GH Cable

    #70168
    $0.99

    The VMX GH cable connects a VMX GH signal connector to an external sensor, breakout board or other device.

    Detailed Specifications:

    • Cable Length: 25 cm
    • Connectors: 4-pin JST-GH (2)
    • Wire Colors: Black, Red, Blue, Green

     

    VMX JST GH to AMP Breakout Board

    #70164
    $8.99

    The VMX GH-to-SH breakout board connects a 4-pin .1" standard connect (sometimes referred to as an "AMP connector").  The connector may either be a standard or a locking variety connector.

    • Board Dimensions:  2" x .75" x .15"
    • VMX-side Connector: JST-GH Connector, 4-pin
    • External Connector:  AMP Male Connector w/support for locking tab (4-pin)

     

    VMX JST GH to SH Breakout Board

    #70165
    $5.99

    The VMX GH-to-SH breakout board connects a 4-pin .1" standard connect (sometimes referred to as an "AMP connector").  The connector may either be a standard or a locking variety connector.

    • Board Dimensions:  2" x .75" x .15"
    • VMX-side Connector: JST-GH Connector, 4-pin
    • External Connector:  AMP Male Connector w/support for locking tab (4-pin)

    VMX Wallwart Adapter Cable

    #70166
    $5.99

    The VMX Wallwart Adapter cable connects a VMX power connector to an external 12VDC Wallwart power supply.

    Detailed Specifications:

    • Cable Length: 25 cm
    • Wire Gauge: 20 AWG
    • VMX-side Connector: JST-VH Wire Colors: Red (power), Black (ground)
    • Wallwart-side Connector:  2.1mm inner diameter, 5.5" outer diameter, center-positive

     

    Zip Ties, Blue, 150mm (100 pack)

    #70010
    $3.49

    150mm Blue Zip Tie, 100 pack, can be used for wire management.

    Specifications:

    • Length: 150mm
    • Material: Nylon
    • Quantity: 100pcs