Display
per page
#70161
$7.49
(In stock)
Used to replace or supplement connector on NI my-DAQ Kit.
#70001EC
$3.99
(In stock)
Extend the reach of your MXP port by using this 8 inch cable to re-position you boards where you need them.
Compatable with MXP accessory boards like the protoboard, RIOduino and myRIO.
Features:
- Keyed male and female 34-pin connectors
- 28 AWG ribbon cable
- 34 conductor
- 8? length
#70016
$3.49
(In stock)
Ideal for the myRIO.
- Inside Contact Diameter: 2.1mm
- Outside Contact Diameter: 5.5mm
- Termination Style:Â Solder Cup
- Voltage Rating:Â 12 V
- 6 Amp
- 1 meter cord length
- 18AWG or 20AWG wire guage
- DC connector type
#71014
$4.99
(In stock)
#71012
$10.00
(In stock)
#70168
$0.99
(In stock)
The JST-GH to JST-GH Cable connects external sensors, breakout boards or other devices.
Detailed Specifications:
- Cable Length: 25 cm
- Connectors: 4-pin JST-GH (2)
- Wire Colors: Black, Red, Blue, Green
#70021
$12.95
(In stock)
The Powerpole Extension Cable is 50cm long and 14AWG wire gauge to handle heavier loads.
#71011
$15.99
(In stock)
This set of 12 pieces includes,
- 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
- 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
- 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
- 6 x 3pin Dupont male to male connectors
#70162
$6.99
(In stock)
#70186
$5.99
(In stock)
USB Cable, Type A to Type C, Blue, 1 Meter, male to male
#70167
$2.99
(In stock)
The VMX Battery Adapter cable connects a VMX-pi power connectcor to an external battery supply.
Detailed Specifications:
- Cable Length: 25 cm
- Wire Gauge: 20 AWG
- Connector: JST-VH Wire Colors: Red (power), Black (ground)
- Wire Free-end: stripped and tinned
#70160
$17.99
(In stock)
Includes:
- 4 JST-GH to 4 Pin Dupont Cables (connects a VMX-pi GH signal connector to an external sensor or device).
- 1 battery adapter cable (connects a VMX-pi power connector to an external battery supply).
- 1 Wallwart cable (cable allows you to connect a VMX-pi to an external 12VDC Wallwart power supply).
#70166
$5.99
(In stock)
The VMX Wallwart Adapter cable connects a VMX power connector to an external 12VDC Wallwart power supply.
Specifications:
- Cable Length: 25 cm
- Wire Gauge: 20 AWG
- VMX-side Connector: JST-VH Wire Colors: Red (power), Black (ground)
- Wallwart-side Connector: 2.1mm inner diameter, 5.5" outer diameter, center-positive
#70010
$3.49
(In stock)
150mm Blue Zip Tie, 100 pack, can be used for wire management.
Specifications:
- Length: 150mm
- Material: Nylon
- Quantity: 100pcs
#70755
$19.99
(In stock)
The Studica Analog Module
#70189
$4.99
-
- 150mm Length
- 3 Position
- TJC8 FH-MC on 2 Split Ends
- TJC8 MH-FC on single end
- Twisted Cable
- Colors: White, Red, Black (red in middle)
- 24AWG Guage