The Studica Robotics RC Servo Arm can be used with the Multi Mode Smart Servo, Multi Mode Smart Servo 200, or most servos with a 25 Tooth gear.

The Studica Robotics 6mm D-Shaft Servo Hub 25T is made of anodized 6061-T6 Aluminum and is used to connect a servo motor to a D-Shaft axle.

The 6mm diameter D-Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

The 6mm x 96mm D-Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

The 6mm x 140mm D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

A twelve pack of 25mm Studica Robotics standoffs used for robotics design builds.

The Studica Robotics 42mm standoffs can be used to space parallel plates, channels, brackets, and more.

A Studica Robotics 25mm male to female (12 pack) standoff for robotics design.

The Studica Robotics 32-tooth gear (2-pack) is ideal for use with robotics design builds.

A Studica Robotics 64-tooth gear (2 pack), for use with robotics design builds.

A Studica Robotics 26-tooth bevel gear for use in robotics design and competitions.

The Studica Robotics 30-tooth bevel gear, 1-1 set (2 pack) is ideal for robotics design builds.

The Studica Robotics 20 Tooth GT2-6mm Timing Belt D-Shaft Pulley can be used with any of the GT2 belts. 

The Studica Robotics 30 Tooth GT2-6mm Timing Belt D-Shaft Pulley can be used with any of the GT2 belts in your robotics builds.

The Studica Robotics GT2-6mm Smooth Idler Pulley, H Type, w/3mm Inner Bore Bearing is ideal for your robotics design builds.

This GT2 (also called 2GT) timing belt has a 2mm Pitch, 6mm width, and open 1000mm in length. Use any of the GT2 pulleys from Studica and the clamp kit.

Specifications:

• type: GT2 open-loop
• pitch: 2 mm
• width: 6 mm
• material: neoprene rubber, fiberglass reinforced
• belt shape: circular tooth profile

GT2-6mm Timing Belt Clamp w/Set Screw

The Studica Robotics 100mm Drive Wheel (4") with an axial width of 25mm, can be used as a simple wheel providing good traction on carpet and tile flooring. They can also be used for intake systems. Use with 1/2" Hex Shaft or 6mm Shaft Hub to use connect 6mm D-Shaft Axles.

The Studica Robotics 100mm (4 inch) Omni Wheel provides rotational and sideways 360° maneuverability.  Great for omni directional movement and rotation, easy direction control and tracking, and for fast turning. Use the Enhanced Wheel D-Shaft Hub Kit with this Omni Wheel.

The 6mm D-Shaft Hub from Studica Robotics is a precision aluminum mounting hub that connects a 6mm D-shaft to wheels or robot components. Ideal for a secure shaft to mounting hub connection. Sold in a pack of 4.

Made of aluminum, the Studica Robotics Clamping 6mm D-Shaft Hub is used with flex and drive wheels.

The Studica Robotics Light Weight 6mm D-Shaft Hub (2 pack) are used with 6mm D shafts. They have a 5mm set screw for tight clamping and seven M3 tapped mounting holes.

The Studica Robotics enhanced D-shaft wheel hub kit is ideal for use with the Omni and Mecanum wheels for a strong axle hold.

The Studica Robotics 6mm D-Shaft Face Bearing Block can be mounted on any channel and bracket allowing for a 6mm ID through hole for 6mm shafts (axles). The block has a permanently installed Standard Sealed Bearing and has 8 x M3 tapped through holes for easy mounting.