Use your student discount on software and other technology products needed for your education. Save on products from top manufacturers such as NI, IBM SPSS, Avid, Chaos, Robert McNeel, and more. Shop input devices, software, electronics, and hardware.
NI Circuit Design Suite combines Multisim 14.3 and Ultiboard software, to offer students a complete set of tools for circuit design, simulation, validation, and layout. The Circuit Design Suite software download helps you design circuits using intuitive and cost-effective tools.
Note: (Only for sale to Students & Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.)
The NI myDAQ student data acquisition device is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The myDAQ is a high-quality instrumentation device that gives students the power to prototype systems and test circuits outside of the classroom and improve comprehension with continuous reinforcement. (This version of the myDAQ is only for sale to students in the USA).
Special Offer: Optional accessory - myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.
Special Offer: Optional accessory - myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.
The National Instruments myRIO-1900 is a portable reconfigurable I/O (RIO) device that students can use to design control, robotics, and mechatronics systems.
For motor control, use the MD2 Motor Driver
Please Note: Base Grad Pack does not include Regression. Refunds are not available for IBM software downloads.
SPSS Statistics only supports 64-bit Operating Systems, please verify compatibility with your OS.
NI myDAQ student bundle for University of North Dakota students includes:
Does not include myDAQ or Protoboard.
The EE201L Electric Lab Partial Kit bundle for University of North Dakota students includes:
NI myDAQ student bundle for University of North Dakota - Majors in EE206L, includes:
NI myDAQ student bundle for University of North Dakota - Majors in ENGR206, includes:
CATALYST Professional is the world's leading geospatial desktop suite, specializing in Remote Sensing, Photogrammetry & Earth Observation Science for optical, and SAR imagery. Easily integrate our powerful image analysis, ortho-mosaicking, and image processing capabilities into your geospatial technology stack. This educational suite addresses the increasingly important role of earth observation information in many academic disciplines and a fast-growing field of high-tech career options. Add a new dimension to a wide variety of academic studies with this professional-grade software that helps you visualize, research and analyze geographic information.Make geospatial image analysis and data visualization a part of your studies with CATALYST Professional for Students.
Makeblock 3D Printer nozzle Bracket A is designed specially for use as the bracket for a 3D Printer nozzle. This component is made from 6061 aluminum with a design for proper mounting and room for the nozzle extrusion. It has a high load capacity and is easy to mount.
The NI myDAQ student data acquisition device is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The myDAQ is a high-quality instrumentation device that gives students the power to prototype systems and test circuits outside of the classroom and improve comprehension with continuous reinforcement. (This version of the myDAQ is only for sale to students in the USA).
Special Offer: Optional accessory - myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.
Special Offer: Optional accessory - myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.
The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier.
Includes,
The kit comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.
The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.
The mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.
Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.
Includes:
Note: mySTEM Project Board comes with US Plug. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately.
Note: Can run on 9 volt battery (included) or external 9 volt power pack.
Programmable Xilinx 7020 FPGA NI ELVIS—The NI Engineering Laboratory Virtual Instrumentation Suite (NI ELVIS) III is an engineering laboratory device developed for project-based learning.
NI Circuit Design Suite combines Multisim 14.3 and Ultiboard software, to offer students a complete set of tools for circuit design, simulation, validation, and layout. The Circuit Design Suite software download helps you design circuits using intuitive and cost-effective tools.
Note: (Only for sale to Students & Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.)
National Instrument's NI myDAQ is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The NI myDAQ is a high-quality instrumentation device gives student's the power to prototype systems and test circuits outside of the classroom while improving comprehension with continuous reinforcement.
The National Instruments myRIO-1900 is a portable reconfigurable I/O (RIO) device that students can use to design control, robotics, and mechatronics systems.
For motor control, use the MD2 Motor Driver
The NI myRIO Embedded Systems Accessory Kit contains common sensors, devices, and a display.
Required for APUS courses: ELEN430, ELEN435, ELEN436, ELEN440, ELEN498, ELEN499
(NI myRIO not included)
The NI myRIO Mechatronics Accessory Kit includes a variety of commonly used motors, sensors, and components.
NI myRIO Starter Accessory Kit Contents
Automate and optimize your data pipeline
The Pixyz plugin ensure your 3D data is optimized for Unity regardless of the source. Going from import to real-time publishing has never been so easy.
With Pixyz’s software, you can quickly import, prep, and optimize your large CAD, mesh and point cloud models for real-time visualizations in Unity.
ThePowerpole Crimp Tool 15, 30, 45 crimping tool provides a positive crimp on the 15, 30 & 45 amp contacts manufactured by Anderson Power Products for the Powerpole® line of products. It has the following features.
Working with printed circuit boards is in the future of every electronic technician. Almost every electronic device today has a printed circuit board and whether you are assembling a PC board or repairing it; you must understand the basics of working with these boards. Good soldering requires practice and an understanding of soldering principles. This solder practice project will help you achieve good soldering techniques; help you become familiar with a variety of electronic components; and provide you with dynamic results.
Tired of buying batteries for your Snap Circuits. With this battery eliminator you won't ever have to buy batteries again. This Snap Circuits adapter works with all versions of Snap Circuits.
Kids can use their imagination to combine SNAP CIRCUITS® with ordinary building bricks and make endless combinations of construction and circuitry.
Compare an electromagnet to a normal magnet! Have lots of fun while learning about electricity and magnetism. Easy-to-use, and will make kids smarter.
Snap Circuits® Student Guide for SC-100/SC-100R. Student Guide has 48 color pages. For an enhanced learning experience because it teaches electronics. Includes quizzes to verify learning.
This kit is a must for the beginner. After practicing your soldering techniques on the special area of the board; you will be ready to assemble this European siren with flashing LED's. This kit also includes a soldering iron and wire cutters. This kit requires soldering.