Introductory Power NI ELVIS Electronics Device—The Integrator Power Electronics Fundamentals Board for NI ELVIS II/II+ is an add-on application board for the NI Educational Laboratory Virtual Instrumentation Suite II (NI ELVIS II) or NI ELVIS II+ for power electronics applications. The Integrator Power Electronics Fundamentals Board for NI ELVIS II/II+ provides both the hardware and lab resources necessary to teach these topics, giving students all components, wires, and instruments needed conduct experiments. The accompanying software includes all lab instructions and provides students with a simple method of conducting and exporting results of experiments for each lab.

The myGrid for NI myDAQ is an AC power grid that will help a student investigate the components of a power grid. The myGrid interfaces with NI myDAQ to demonstrate energy monitoring, energy conservation, and the concept of the smart grid. The system includes a traditional power source through a motor representing fossil fuels and a renewable power source using a solar panel. It models how power is generated, transmitted, and distributed in a residential setting across three houses.

The myParts kit from Texas Instruments comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more.

NI Circuit Design Suite Student Edition combines Multisim 14.3.1 and Ultiboard PCB Design Software, to empower students with a complete set of professional CAE tools from schematic capture for circuit design, digital and analog circuit simulation and validation, also includes UltiBoard the advanced PCB layout software.

Note: (Only for sale to Students and Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.  No returns or refunds for any download products.)

Programmable Xilinx 7020 FPGA NI ELVIS—The NI Engineering Laboratory Virtual Instrumentation Suite (NI ELVIS) III is an engineering laboratory device developed for project-based learning.

The NI myDAQ student data acquisition device is designed to give students the ability to work on various electronic engineering course work and experiment hands-on with their projects anywhere, anytime. The NI myDAQ is a high-quality electronic lab instrumentation device that gives students the power to prototype electronic systems designs, control systems designs and electronic test circuits outside of the classroom and improve their comprehension with continuous reinforcement. Note: This version of the myDAQ is only for sale to students in the USA.

The  mySTEM™ Control & Project Board for NI myDAQ is an essential tool for the introduction of control systems. It is ideal for teaching and learning science, technology, engineering and mathematics. The mySTEM™ Project Board comes with learning resources that may be used by any beginner in the STEM field to gather data, make decisions and control output devices. It allows students to control the state and direction of four output channels that support a wide range of field devices.

Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. We recommend the Spare Parts Store to create your own project.

Includes:

• Mini Switch
• Built-in voltage regulator
• H-Bridge Motor Drivers for motor control
• Resistors
• Wires
• Flat plugs
• Breadboard prototyping area
• myDAQ connector

Note:  mySTEM Project Board comes with US Plug wall adaptor. You can easily use into different plug with common US->EU or other adapters. Additional Motors, encoders, lights, wiring, solenoids, electromagnets and any other component may be purchased separately. 

This student bundle for University of North Dakota - EE313L, includes:

• 1 - 10K OHM 5% 1/4W AXIAL Resistor
• 1 - 1K OHM 5% 1/6W AXIAL Resistor
• 1 - 100 OHM 5% 1/4W AXIAL Resistor
• 1 - 120 OHM 5% 1/4W AXIAL Resistor
• 1 - 200 OHM 5% 1/6W AXIAL Resistor
• 1 - 5 OHM 5% 5W AXIAL Resistor
• 1 - 16K OHM 5% 1/4W AXIAL Resistor
• 1 - CER 1UF 25V X7R RADIAL Capacitor
• 1 - FIXED IND 10MH 170MA 10.86OHM TH
• 1 - FIXED IND 1MH 100MA 20 OHM TH
• 1 - SWITCH SLIDE SPDT 0.4VA 28V
• 1 - CER 10UF 50V X7S RADIAL Capacitor
• 1 - CER 10000PF 400VAC Y5V RAD Capacitor
• 1 - 16 OHM 5% 1/4W AXIAL Resistor
• 1 - Carbon Film 20 Ohm 1/4 Watt 5% Resistor
• 1 - Carbon Film 8.2k Ohm 1/4 Watt 5% Resistor

The ultimate 3D rendering and fluid dynamics toolset for education. The V-Ray® Education Student License offers students access to multiple V-Ray® versions, Chaos® Phoenix, Chaos Scans, Chaos Cloud, Chaos Vantage, and Chaos Player in a single collection so you can focus on your art without worrying about numerous licenses.

The curve tracer instrument in WaveForms allows several of the Discovery family of devices to draw characteristic curves of common devices like diodes, NPN and PNP transistors, and both P- and N-type FETs. 

The BNC Adapter for Analog Discovery provides this connection method to both the waveform generator and oscilloscope instruments, while keeping the option and convenience of the standard MTE cables for the other 10 instruments on the Analog Discovery 2 and Analog Discovery 3.