Close
Main Categories
    Filters
    Preferences
    Search

    myDAQ for Students - Hardware only

    The NI myDAQ student data acquisition device is designed to give students the ability to work on engineering course work and experiment with projects hands-on anywhere, anytime. The myDAQ is a high-quality instrumentation device that gives students the power to prototype systems and test circuits outside of the classroom and improve comprehension with continuous reinforcement. (This version of the myDAQ is only for sale to students in the USA).

     

    Special Offer: Optional accessory -  myGRID for NI myDAQ - an AC power grid that helps to investigate the components of a power grid - is available as a bundled purchase - click the checkbox below - while supplies last.

    Students - Current academic verification is required to purchase this product.

    MFR Part #: 781325-01
    $219.97
    Availability: In stock
     
    Software is Windows only.

    NI myDAQ allows students to complete engineering coursework, prototype systems, test circuits, and experiment with projects hands-on anywhere, anytime. Here's what's included.

    Two Differential Analog Input and Analog Output Channels (200 ks/s, 16 bit, +/- 10 Volts)
    Access matched analog input and output channels in a +/- 10 volt range through the screw terminal connectors or +/- 2 volt range through the 3.5mm audio jacks.
     

    +5 , +15, and -15 Volt Power Supply Outputs (up to 500m Watts of Power)
    USB powered for maximum mobility, myDAQ supplies enough power for simple circuits and sensors.
     

    Eight Digital Input and Digital Output Lines (3.3 Volt TTL-Compatible)
    Use software-timed digital lines for interfacing both Low Voltage TTL (LVTTL) and 5 volt TTL digital circuits. Each line is individually selectable for input or output.
     

    60 Volt Digital Multimeter (DMM) for Measuring Voltage, Current, and Resistance
    The isolated DMM includes the capability to measure both AC and DC voltage and current as well as resistance, diode voltage, and continuity.
     

    Reusable Storage Box with Storage Tray, DMM Probes, and Audio Cable
    The box and storage tray provide convenient storage for your NI myDAQ and included USB cable, DMM probes, audio cable, as well as your own components and accessories.

    View User Guide and Specifications [Click Here]

    What's included:

    • data acquisition device
    • USB Cable
    • DMM Probes
    • Audio cable (3.5mm)
    • Screw Terminal connector and NI screwdriver
    • Getting Started Card
    • TI Design Competition & Samples Program Card
    • Reusable Storage Tray



    The myDAQ is a single device that has eight commonly used plug-and-play computer-based lab instruments. With this device, the computer becomes an engineering instrument.

    Designed by National Instruments with high-quality Texas Instruments Analog Integrated Circuits (ICs), the hardware system diagram and list of Texas Instruments IC's in the user guide depicts how TI data converters, amplifiers, and interface and power management circuits were used in the design of NI myDAQ.

    Extend the device's capabilities with LabVIEW and Multisim. Verify homework solutions with real signals using Multisim for circuit simulation and LabVIEW for automating measurements and performing signal processing.

    Technical Support

    Get tips on using the three different software platforms, troubleshoot problems with your NI myDAQ, and/or ask your own questions on the discussion forum - link is listed below.

    Write your own review
    • Product can be reviewed only after purchasing it
    • Only registered users can write reviews
    • Bad
    • Excellent
     
    Software is Windows only.

    NI myDAQ allows students to complete engineering coursework, prototype systems, test circuits, and experiment with projects hands-on anywhere, anytime. Here's what's included.

    Two Differential Analog Input and Analog Output Channels (200 ks/s, 16 bit, +/- 10 Volts)
    Access matched analog input and output channels in a +/- 10 volt range through the screw terminal connectors or +/- 2 volt range through the 3.5mm audio jacks.
     

    +5 , +15, and -15 Volt Power Supply Outputs (up to 500m Watts of Power)
    USB powered for maximum mobility, myDAQ supplies enough power for simple circuits and sensors.
     

    Eight Digital Input and Digital Output Lines (3.3 Volt TTL-Compatible)
    Use software-timed digital lines for interfacing both Low Voltage TTL (LVTTL) and 5 volt TTL digital circuits. Each line is individually selectable for input or output.
     

    60 Volt Digital Multimeter (DMM) for Measuring Voltage, Current, and Resistance
    The isolated DMM includes the capability to measure both AC and DC voltage and current as well as resistance, diode voltage, and continuity.
     

    Reusable Storage Box with Storage Tray, DMM Probes, and Audio Cable
    The box and storage tray provide convenient storage for your NI myDAQ and included USB cable, DMM probes, audio cable, as well as your own components and accessories.

    View User Guide and Specifications [Click Here]

    What's included:

    • data acquisition device
    • USB Cable
    • DMM Probes
    • Audio cable (3.5mm)
    • Screw Terminal connector and NI screwdriver
    • Getting Started Card
    • TI Design Competition & Samples Program Card
    • Reusable Storage Tray



    The myDAQ is a single device that has eight commonly used plug-and-play computer-based lab instruments. With this device, the computer becomes an engineering instrument.

    Designed by National Instruments with high-quality Texas Instruments Analog Integrated Circuits (ICs), the hardware system diagram and list of Texas Instruments IC's in the user guide depicts how TI data converters, amplifiers, and interface and power management circuits were used in the design of NI myDAQ.

    Extend the device's capabilities with LabVIEW and Multisim. Verify homework solutions with real signals using Multisim for circuit simulation and LabVIEW for automating measurements and performing signal processing.

    Technical Support

    Get tips on using the three different software platforms, troubleshoot problems with your NI myDAQ, and/or ask your own questions on the discussion forum - link is listed below.

    Customers who bought this item also bought

    Breadboard and Jumper Wire Kit

    #9880WK
    $10.95 $11.50
    (61 In stock)
    This NI Breadboard is a 830 tie point breadboard that comes with a 70 piece jumper wire set designed for use with National Instruments my-DAQ portable data acquisition device.

    myParts Kit from Texas Instruments: Companion Parts Kit for NI myDAQ

    #6002-240-001
    $95.00
    (21 In stock)

    Get your students quickly involved in building essential electronic circuits using myParts Kit supported by the Texas Instruments® University Program. The set of key components in the myParts Kit encourages hands-on experimentation with breadboards of basic circuitry, helping to make learning productive and enjoyable for beginners and more advanced students alike. Hobbyists and independent developers will also find the kit useful for investigating their design concepts. The kit comes with a collection of parts that are the building blocks of all electronics, including op-amps, an instrumentation amplifier, a comparator, voltage regulators, switching regulators, digital logic gates, timers, temperature sensors, data converters, transistors, resistors, capacitors, LEDs, switches, a wiring kit and more. myParts Kit enables your students to run experiments that help them understand real-life applications in areas such as power management, audio amplification, spinning motors, light detection, signal conditioning, data acquisition, and telecommunications to name a few.

     

    myDevBoard - Prototype Board

    #70752
    $40.48
    (301 In stock)

    The myDevBoard is an accessory board designed to connect directly to the NI myDAQ hardware. The Protoboard consists of a prototyping space as well as each I/O line from NI myDAQ broken out through quad contact blocks to make wiring easier. 

     

    Includes,

    • NI myDAQ terminal block and female headers
    • 9 V battery holder to add supplemental voltage and current
    • Includes switch to select between battery or external power using AC Adapter or bench top power supply. (Battery, AC adapter and bench top power supply not included)
    • 3 AMP Auto reset fuse
    • Segmented power rails on main bread board
    • Large ground plane underneath main bread board 

    NI Circuit Design Suite - Student Edition - Multisim Download

    #779897-35
    $62.95
    (In stock)

    NI Circuit Design Suite combines Multisim 14.3 and Ultiboard software, to offer students a complete set of tools for circuit design, simulation, validation, and layout. The Circuit Design Suite helps you design circuits using intuitive and cost-effective tools.

     

    Note: (Only for sale to Students & Faculty in the USA for lab preparation on personal computers, not for classroom or institutional use.)

    myProto Protoboard

    #6002-410-007
    $49.99
    (10 In stock)

    The Digilent myProto accessory board for the NI my-DAQ and NI my-RIO brings all your my-DAQ/my-RIO's signals to breadboard connections where they can be easily accessed using simple jumper wires, and even adds several useful I/O devices.