Main Categories
    Filters
    Preferences
    Search

    Makeblock Air Pump Motor DC 12V/3202PM

    Makeblock air pump motor - DC 12V/3202PM is widely used for aquarium tank oxygen circulate, it can also be used for a DIY project that you dream up.

    MFR Part #: 50001
    $2.00
    $7.99
    14 in stock

     

    Specification for Air Pump Motor DC:

    • Rated voltage: DC 12V
    • Load: Air
    • Current (With load): Less than 400mA
    • Flow : 1.8LPM
    • Size : D27 x 52mm
    • Maximum pressure : More than 600mmHg
    • Noise: Less than <60dB
    Write your own review
    • Product can be reviewed only after purchasing it
    • Only registered users can write reviews
    *
    *
    • Bad
    • Excellent

     

    Specification for Air Pump Motor DC:

    • Rated voltage: DC 12V
    • Load: Air
    • Current (With load): Less than 400mA
    • Flow : 1.8LPM
    • Size : D27 x 52mm
    • Maximum pressure : More than 600mmHg
    • Noise: Less than <60dB
    Customers who bought this item also bought

    Makeblock MG995 Servo Hub

    #69001
    $1.19 $4.75
    ( 1 In stock)

    The Makeblock MG995 Servo Hub is a aluminium high quality part ideal for fitting JR standard, FUTABA standard servos.

    Makeblock 42BYG Geared Stepper Motor

    #80502
    $14.08 $56.31
    ( 10 In stock)

    Makeblock 42BYG geared stepper motor is a simple, but very powerful stepper motor with high output torque and response speed but low noise and energy consumptionhas better performance.

    It comes with higher torque than 42BYG stepper motor. It can be used as the power motor of some high-performance machine.

    Specification:

    • Step Angle (degrees) :1.8
    • Phase Current: 2.8A
    • Wire Number: 4
    • Motor Length: 56mm
    • Ratio: 5.18:1
    • Output Shaft: D shaft 8mm

    Makeblock 57BYG Stepper Motor Bracket - Pair in Black

    #62040
    $1.66 $6.66
    ( 7 In stock)

    The Makeblock 57BYG Stepper Motor Bracket can be used as the structural support or connection point for Makeblock 57BYG Stepper Motor.

    Makeblock Me Slide Potentiometer

    #13614
    $1.25 $4.99
    ( 66 In stock)

    Me Slide Potentiometer is one type of potentiometer that can be used to control volume, light intensity, motor speed, movement control, etc. in interactive projects.

    Features

    • Compatible with the Arduino sensor expansion board;

    • Three 4mm mounting holes and one RJ25 port for easy assembling;

    • With one red power indicator and one blue potentiometer indicator;

    • Anti-reverse connection protection feature.

     

    How Does It Work?

    This Me Slide Potentiometer can be combined with Me Orion (or other Arduino IO/sensor expansion board) in interactive projects. Move the lever from one side to the other, its output voltage will range between 0 V to the VCC you apply. The VCC Me Slide Potentiometer supports vary from 3.3V to 5V.
     

    Note

    If you connect this module to Me Orion, please make sure you connect it to port 6, port 7 or port 8.

    Makeblock Me Compass

    #11024
    $3.25 $12.99
    ( 60 In stock)

    The Makeblock Me Compass is a 3-axis digital compass. The main chip is Honeywell HMC5883L. On-board regulator provides stable power for HMC5883L.

    USB cable type A/B

    #A000045
    $0.95 $3.99
    ( 88 In stock)

    Standard USB 2.0 cable. Use it to connect Arduino Uno, Arduino Mega 2560, or any board with the USB female A port of your computer. Cable length is approximately 178cm.

    Makeblock Me Temperature and Humidity Sensor

    #11032
    $2.50 $9.99
    ( 0 In stock)

    The Makeblock Me Temperature and Humidity Sensor contains a calibrated digital signal output. It adopts specific digital module collecting technology and temperature-humidity sensing technology to ensure high reliability and excellent long-term stability. This Makeblock sensor can measure the temperature from 0? to 50?. Users can use it to build a cost-effective temperature and humidity monitoring system. Its yellow ID means that it has a single-digital port and needs to be connected to the port with yellow ID on Makeblock Orion.

    Makeblock Me Touch Sensor

    #11020
    $2.50 $9.99
    ( 42 In stock)

    The Makeblock Me Touch Sensor will be triggered by finger touch. Users can also connect the "TOUCH" pinhole to metal and touch the metal to trigger the sensor. This touch sensor give you the ability to adjust the sensitiity to fit your project. It needs 0.5s for the self-calibration after energized.

    Makeblock Versatile Cable with Stripped Ends - 35cm, 22AWG (Pair)

    #14240
    $1.25 $4.99
    ( 5 In stock)

    The Makeblock Versatile Cable with Stripped Ends can be used for Makeblock Air Pump Motor Water Pump Motor and in a variety of DIY projects.